Jump to content

Reassembling gears

tucker810

By tucker810
in Watch Repairs Help & Advice

 Share

Recommended Posts

tucker810 New Member

tucker810

Posted
Posted

I just took apart my first working watch and I am having trouble with the three gears. Everything else is easy to reassemble but the three gears leading to the mainspring. How do you guys put them back together? I am new to this so any help would be greatly appreciated.

  • Confused 1
mousekar Member

mousekar

Posted
Posted

If I understand you correctly, I believe you’re talking about the gear train? It takes some practice, a lot of patience and persistence. It can be done! Some are easier than others I have found.
I am only a hobbyist, so someone who is more trained then I am, may be able to offer better advice.
The technique that gets me the best results, is to very gently apply a small amount of pressure (just enough to keep it in place) either with peg wood, or with my finger while I hold the movement, and use my tweezers to individually move the gears in place. When all the pivots are in, the plate will fall into place. DO NOT push down, or you may bend a pivot! DO NOT force anything. These are delicate pieces of fine mechanics. Tolerances are very exact.
I’ve picked this up from watching a substantial amount of videos. So just watch videos of movements being assembled by people who know what they’re doing (there are a number by hobbyists, and while interesting are not as refined) and you’ll pick up a lot of proper techniques.
Hope that helps!
Cheers


Sent from my iPhone using Tapatalk

mousekar Member

mousekar

Posted
Posted

Edit: I meant to say “bridge”. Place the gears in the pivots correctly, place the “bridge” on top VERY gently and apply a small amount of gentle pressure with peg wood or finger on the bridge to keep it in place while you use your tweezers to adjust the gears to get the top pivots in the “bridge” (not plate).
I’ve also seen and done, putting the bridge in place and then putting in the bridge screws but NOT tightening them down (very important). You have to allow some play in the bridge so you can adjust the gears to get the pivots in. Either way, I would check out some videos first, see a pro like Mark Lovick do it a few times and then give it another go. If you get frustrated, walk away because you may try to force something at that point, and that’s when things go flying or break.
Good luck. You can do this! Hope this helps.


Sent from my iPhone using Tapatalk

tucker810 New Member

tucker810

Posted
  • Author
Posted
9 hours ago, mousekar said:

If I understand you correctly, I believe you’re talking about the gear train? It takes some practice, a lot of patience and persistence. It can be done! Some are easier than others I have found.
I am only a hobbyist, so someone who is more trained then I am, may be able to offer better advice.
The technique that gets me the best results, is to very gently apply a small amount of pressure (just enough to keep it in place) either with peg wood, or with my finger while I hold the movement, and use my tweezers to individually move the gears in place. When all the pivots are in, the plate will fall into place. DO NOT push down, or you may bend a pivot! DO NOT force anything. These are delicate pieces of fine mechanics. Tolerances are very exact.
I’ve picked this up from watching a substantial amount of videos. So just watch videos of movements being assembled by people who know what they’re doing (there are a number by hobbyists, and while interesting are not as refined) and you’ll pick up a lot of proper techniques.
Hope that helps!
Cheers


Sent from my iPhone using Tapatalk

This is really helpful! Thanks, can you recommend any good videos?

  • 1 month later...
 Share
Go to topic listing


  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • watchhammer
      Looking to try servicing an old movement

      By watchhammer · Posted

      As a fellow newbie who's made a bunch of mistakes over the past year or 2 I'd like to offer my experience. I didn't start with a new practice movement, I started with 1970s Tissot that I loved. If I could do it over I would still use a vintage watch for my first movement. I wouldn't, however, chose one I cared about or that was expensive. It also had a calendar complication- dont do that. I learned a lot about part compatibility and movement families right away though! Emmy watch and Ranfft are great resources for this! I would start with the Benrus and go ahead and find a parts movement right away YOU WILL BREAK AND LOSE PARTS! Get good tweezers, it's much harder to handle tiny springs than YouTube would suggest. And be extra carful, pivots don't like to be forced into jewels - bridges are a real pain in the ass at the start. Don't be afraid to use your bare hands to hold parts/bridges and handle the movement. Finger cotts can come later. Be as carful as possible with hairsprings, this can ruin all the fun!  Buy a cheap demagnitizer. For me, I think its fine to buy cheap tools in the beginning and replace as you go. But some things I wish I'd have spent more money on right of the bat - TWEEZERS and Rodico (don't get the fake stuff). There's a great thread here on Chinese tools. I used a cheap digital microscope for a long time. I got quite good at working under it even with no depth perception. It's probably better to just use loupes but I think it helped me be more mindful and it was great for inspection. I now have a stereo microscope and if you get really into this hobby, it's a must. I cleaned everything by hand in the beginning. This is great for getting familiar with each part and learning to inspect for faults. Peg your jewels! I still hand clean a lot of parts before the ultrasonic. I still use JUST Naptha and IPA and I think thats adequate for my hobby purposes but maybe I'll have moved up in another year. I swish the shellaced parts in IPA for a few seconds to rinse (don't tell anyone). I used to dry each part on a sheet of paper with a puffer. Again, this is good for getting to know each part. I now dry everything in a food dehydrator. Im not going to give any advice on oil because thats suicide. But... until very recently I used just mobius 8000 and Molycote DX for everything. I dont know if I would do it differently If I were to go back but its definitely cheap and it will teach you how to apply oil.  Take a picture after every move even if it's just scratching yourself.  Wind mainsprings by hand until you decide you like the hobby, spend that winder money on tweezers and parts movements. This place is great, there are a bunch of incredible KNOWLEDGEABLE guys willing to help you. Unfortunately, this is as much as I can help, as I'm nowhere near their level.  Oh... and buy a big magnet. Still one of my favorite watches and it reminds me of all the broken pivots and pinged springs every time I put it on.   worth every penny.      
    • mbwatch
      Watch of Today

      By mbwatch · Posted

      @RichardHarris123is that a pony chrono pusher?
    • RichardHarris123
      Watch of Today

      By RichardHarris123 · Posted

      The most important watch repair ever.  No not a long lost John Harrison or the like but my three year old granddaughter's.  £2.99 but "Grandpa, my watch is broken, can you fix it.  How could I say no?
    • RichardHarris123
      Hello and thank you in advance.

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • jeffandy
      Omega 1337 Quartz Movement Running Really Fast

      By jeffandy · Posted

      Omega Cal 1337 Quartz Movement - I repaired (or so I thought) my first full movement from spare parts from not working movements. Everything seems to be running smoothly except its running probably 5-8 seconds fast per minute.  Any thoughts?
×
×
  • Create New...