Jump to content

Pratina

PhilB

By PhilB
in Your Watch Collection

 Share

Recommended Posts

PhilB WRT Addict

PhilB

Posted
Posted

My second project arrived today, I managed to grab this for £8 delivered from ebay.

 

I don't know anything about the make but the colours caught my eye (and the price).

 

It ticks a few seconds then stops. Looking forward to stripping and seeing if I can find the cause.

 

 post-302-0-34934000-1411050305_thumb.jpg

 

 

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted

I would say that at this stage it is better to get some more movements and practice strip-downs and re-assembly. Putting this one aside and then enjoying the challenge of fitting the new jewel at another time when you have more kit.

But if you do wish to have a go then it's not a particularly difficult job, but to do it properly you will need a jewelling kit which are not cheap - from £150 upwards for a reasonably good used set.

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
PhilB WRT Addict

PhilB

Posted
  • Author
Posted

I would say that at this stage it is better to get some more movements and practice strip-downs and re-assembly. Putting this one aside and then enjoying the challenge of fitting the new jewel at another time when you have more kit.

 

I thought as much, it was only £8 so it's not worth too much trouble and expense. 'Tis a shame tho.

 

Thanks

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • MapleWood
      Help - London Elliott Mantle Clock Night Silence

      By MapleWood · Posted

      I've managed to adjust it. I'm going to try and explain it as well as I can with my limited horology knowledge but I hope it helps someone in the future. There is a cam to the right of the front plate as shown in the picture. As the clock ticks along, the pin indicated in the gear comes around and slots into one of the silencer cam gaps, turning the cam. The pin completes a full rotation in 2 hours. To adjust the cam to start at the right time set the clock to just before 7. I did 6:45. Then I turned the silencer cam anticlockwise, which spins freely, until it pushed the silencer lever up and was placed just before the drop. Just before the 7AM indicated in the picture. All I then had to do was progress the hands to 7-7:15which made the pin slot into the silencer cam gap and turn the cam so the lever comes down again, unsilencing the clock. That was it. If anyone comes across this issue again I'd be happy to assist. Thanks again to everyone that helped.
    • Waggy
      Epilame / Fixodrop

      By Waggy · Posted

      Now I'm completely confused, it would appear that the epilame  is oleophobic  as @Marc states: This oleophobic  behavior can be seen as beading of the droplet (as above) which stops the oil spreading which is supported by what we observe on treated/untreated cap stones (for example), but as @VWatchie states this should make the drops more mobile, and not less mobile which is the opposite of what we want. In fact this beading and high mobility are desirable properties in things like smart phone covers, see below.  I am fairly sure that epilame doesn't make the droplets more mobile, so maybe its a strange coating with dual properties that are both oleophobic and cohesive/adhesive resulting in low mobility?? This may explain the high price??  
    • nickelsilver
      Balance wheelwheel crooked

      By nickelsilver · Posted

      The description there is exactly how it's done, and it's very well written!
    • HectorLooi
      What is the correct way to lubricate clock mainsprings?

      By HectorLooi · Posted

      Would it be correct to say that the stronger the mainspring, the thicker the oil should be? So for a fusee mainspring, should a thick grease be used?
    • mikepilk
      Vintage pocket watches from e-bay (winding stems needed)

      By mikepilk · Posted

      I started on pocket watches as they are easier to work on than wristwatches. Many had gold cases, which is why there are so many movements for sale. I was always on the look out for cases, for as Nickelsilver says,  a 16s movement will fit any 16s case* (with tweaks to the stem). I also started hand winding mainsprings, before I had winders. It can be done without damage, but it's quite hard on the fingers.  But you can make homemade winders, see here      * some movements, eg "railroad grade", have a setting lever on the edge of the  dial at about the 1 -2 o'clock, so need a special case.
×
×
  • Create New...