Jump to content

Good Thread Die Set?

Titanium

By Titanium
in Tools & Equipment

 Share

Recommended Posts

Titanium Watch Enthusiast

Titanium

Posted
Posted

About 2 mouths ago I got myself a Unimate 3 lathe and I've really been enjoying playing around with it. Now I'd like to have a go at making screws for watches and was wondering if anyone knows of a good set or source of mini dies, thread gauges and the inserts I will need for lathing nonstandard threads?

 

Any help would be appreciated. Thanks.

Link to comment
Share on other sites
rodabod Distinguished Member

rodabod

Posted
Posted

I can recommend the 31 piece HSS watchmakers set which comes branded under many names. I've cut stem threads and made screws with mine and it's incomparable to the cheap Indian carbon-steel taps and die plates which you get.

Link to comment
Share on other sites
khunter WRT Addict

khunter

Posted
Posted

All I can say is good luck. With American pocket watches alone there are literally dozens of thread pitch/diameter combinations, and that's just with one manufacturer. Swiss or more generally European will probably be more metric based but there again, each manufacturer probably has their own specific sizes. Threading a screw hardly bigger than a grain of sand in some cases (jewel settings, small wrist watches, etc) would present even more challenges. If you have any luck let us know!

Link to comment
Share on other sites
khunter WRT Addict

khunter

Posted
Posted
On 1/27/2018 at 12:26 PM, rodabod said:

I can recommend the 31 piece HSS watchmakers set which comes branded under many names. I've cut stem threads and made screws with mine and it's incomparable to the cheap Indian carbon-steel taps and die plates which you get.

If it's the metric set that I found in searching it would be of no use for American pocket watches, here's an image of page 1 of 8 of screws just for Elgins, and they are all in inches. Some jewel setting screws are 480 tpi, and some on this page are above 300. My guess is old time screws were rolled, as modern mass produced screws are, then cut to length and then the head and slot were formed last. I see no other way to mass produce such small pieces individually. Occasionally I have seen Elgin tap sets on ebay, and they sell for a mint when they appear. 

2018-01-28 19.09.35.jpg

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Murks
      Digital Watch

      By Murks · Posted

      does anyone knows what type of battery this digital Watch takes?  
    • Neverenoughwatches
      Second hand watch market.

      By Neverenoughwatches · Posted

      Hello good watch folk ,I  just fancied a light hearted discussion after my head was starting to spin over Epilame 😅. Specifically I'm meaning the sale of vintage watches, say nothing past the 1980s market. The stuff we see on ebay and other similar sites and found at carboots, curio shops etc. And are  we thinking its reaching a peak volume ?  Younger generations clearing out passed parents and grandparents possessions.  The younger folk are not as sentimental as the old fogies ( I'm now nearly at an age that i used to think was old fogie age ). When might it have started ?  i often wish i discovered the hobby much much sooner when selling your grandfathers pocket watch at a boot sale for a few quid was just a way to offload some tat. And when might it slow down. Thoughts anyone ?
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Yes i did eventually realise that the oil will act as a barrier, I'm sure the discussion will continue. Ive had two oleophobic coffees ( added coconut ) and in the meantime i have this just delivered to take my mind off epilame for the time being. My favourite type of dial, its a beautiful looking watch traditional English made and it runs,  the ticktock is phenomenal,  i can hear it across my living room .  You wont believe how much it was. Thats interesting about synthetic oils , i thought the same, going from a 2 year service to 5 years is a big drop in income for service folk.  I expect some did well when they embraced the use of synthetic,  probably drawing in more customers than those that didn't use the new fangled substances , i bet fairly short lived though. The more frequent service makes more sense to me, not for just the service but for the regular check up inspections that might pick up impending faults. As far as epilame goes, wouldn't it be great to be able to fumigate the complete movement in a sealed jar of heated stearic acid, 🤔 now theres a thought 😅.
    • Albyon
      AS2031-57E solar panel - mission: impossible

      By Albyon · Posted

      Imm going to close the discussion by attaching the photo of my super-titanium after several vicissitudes finally working. Purchased as not working I replaced the battery and for a stroke of luck I found its semi-new solar panel which, having verified its operation, seems to recharge the accumulator perfectly. I had taken this watch almost by bet, with 40 euros I brought it back to life. The initial half idea was to resell it to finance another purchase, but.. it's definitely a nice item. It would need to check the impermeability but it's a pleasure to see it on the wrist 😃
    • Albyon
      Insert the movement inside the case

      By Albyon · Posted

      In fact the secret is to go gently and find the way without forcing, and the movement enters without problems
×
×
  • Create New...