Jump to content

Enicar glass with marked ring

Massimo

By Massimo
in Watch Repairs Help & Advice

 Share

Recommended Posts

Massimo Member

Massimo

Posted
Posted

Hi all,

I need to replace the glass of an Enicar watch, which has a marked ring on the inside.

The glass is an acrylic, domed, snap in, 31mm diameter.

I bought a standard glass but the ring did not fit inside.

The ring is 30mm diameter, 1 mm thickness.

I found the sternkreuz ST is sold by 2 diameters(inside outside) , which is what I need, but I'm not sure about the height of it.

Does anybody know if I can fit this 1mm ring inside?

Cousins does not want to give me the info...

Thanks a lot in advance! 3281a70c9c7825d6a6103775677f4e30.jpg

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted

That is always hard to find. Have had that problem a few times. Last was now when i repaired a Atlantic compressor . That had a stepped ring inside. Where the dial should sit. The old ring would work so i came up with a trick that i used before. i turned the ring inside out. Making the dial center on the bezel and sit a little lower. Works nice and you can't see that i have turned it from the outside. 

Try tiptopcrystal also.  He has GS and Stella crystals. 

Link to comment
Share on other sites
Massimo Member

Massimo

Posted
  • Author
Posted
That is always hard to find. Have had that problem a few times. Last was now when i repaired a Atlantic compressor . That had a stepped ring inside. Where the dial should sit. The old ring would work so i came up with a trick that i used before. i turned the ring inside out. Making the dial center on the bezel and sit a little lower. Works nice and you can't see that i have turned it from the outside. 
Try tiptopcrystal also.  He has GS and Stella crystals. 
Hi Rogart, how do you mean inside out? Mi ring is stiff metal, I can't turn it inside out...
Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted
12 hours ago, Massimo said:
On 12/10/2017 at 12:12 PM, rogart63 said:
That is always hard to find. Have had that problem a few times. Last was now when i repaired a Atlantic compressor . That had a stepped ring inside. Where the dial should sit. The old ring would work so i came up with a trick that i used before. i turned the ring inside out. Making the dial center on the bezel and sit a little lower. Works nice and you can't see that i have turned it from the outside. 
Try tiptopcrystal also.  He has GS and Stella crystals. 

Hi Rogart, how do you mean inside out? Mi ring is stiff metal, I can't turn it inside out...

Sorry mean upside down. Not inside out. 

Link to comment
Share on other sites
  • 1 month later...
Massimo Member

Massimo

Posted
  • Author
Posted

It finally worked with a little bit of sandpaper on the edges, to facilitate the insertion...but now another issue: does anybody see the pin to unlock the stem? I opened the watch long ago and I forgot how I did it!;)8580ac8517cb852c68bcbde6cf85fa1a.jpg

Sent from my Le X829 using Tapatalk

Link to comment
Share on other sites
ro63rto Distinguished Member

ro63rto

Posted
Posted
It finally worked with a little bit of sandpaper on the edges, to facilitate the insertion...but now another issue: does anybody see the pin to unlock the stem? I opened the watch long ago and I forgot how I did it![emoji6]8580ac8517cb852c68bcbde6cf85fa1a.jpg&key=b2d4f967edc62b1abe22970140a5d231528bafbc7e7baec8c67e20acf3f8f4a5

 

Sent from my Le X829 using Tapatalk

 

 

It's one of the screws near the stem.

Watch them when you pull out the stem, the correct one will move slightly.

Just remember, 1 to 1.5 turns ONLY to release stem. Too much and it's dial off time.

 

Link to comment
Share on other sites
Massimo Member

Massimo

Posted
  • Author
Posted
It's one of the screws near the stem. Watch them when you pull out the stem, the correct one will move slightly.
Just remember, 1 to 1.5 turns ONLY to release stem. Too much and it's dial off time.
 
Thanks Roberto!I'll be careful...:)

Sent from my Le X829 using Tapatalk

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      Help Identifying movement

      By rjenkinsgb · Posted

      It looks similar to some AS movements, but it's not identical to any I can find. There may be a logo / number under the balance wheel??  
    • rjenkinsgb
      Accutron 218 transistors

      By rjenkinsgb · Posted

      Many would disagree: https://www.rohm.com/products/faq-search/faqId/234 https://uk.farnell.com/c/semiconductors-discretes/transistors/bipolar-transistors/pre-biased-digital-bipolar-transistors https://uk.rs-online.com/web/p/bipolar-transistors/8232832P?gb=s https://uk.rs-online.com/web/p/bipolar-transistors/0580240?gb=s (RS don't have a specific category, but over 1000 "digital transistor" items).  
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Thanks, ManSkirtBrew.  I started looking for a setup like yours and ran across this.  It was about half the price of the JKA Feintaster (depending on what auction you were in), and it's a Bergeon.  I bought it because I thought the price was fair (eBay - Buy it now), and I'm a sucker for vintage tools. It also has a table, so it should be easy to use for measuring jewels. I wonder if the the contact points can be changed out. Bergeon seems to manufacture new tables and accessories for the contemporary dial version. What do you guys think of it? I'm sorry this post seems to have taken a detour. I'm new here so let me know if I should start a new topic.
    • nevenbekriev
      Winding pinion making

      By nevenbekriev · Posted

      This is a flying cutter, usual one. The cutter itself is shown in the pictures in the first message, it is made of broken tungsten carbide drill bit. I asure that all the angles of the cutter are as they should be. I have video - little older one - that I made when onse making the same kind of winding pinion for a Poljot 2200, which is even smaller than this one. It is not easy to see in the video, but the tool rest moves about 1mm towards the object in Y direction and then returns back untill cutter is rotating. Then the spindle is rotated one tooth ahead and everything repeated untill all teeth are cut.
    • Trav2004
      Help Identifying movement

      By Trav2004 · Posted

      After a bit further research could it possibly be an AS 970?
×
×
  • Create New...