Jump to content

How to reassemble Vostok balance complete?

szbalogh

By szbalogh
in Watch Repairs Help & Advice

 Share

Recommended Posts

oldhippy Distinguished Member

oldhippy

Posted
Posted

Why did you remove the hairspring from the balance cock? You should have just removed the end stones to clean the balance holes, also if you have a good watch cleaning machine and the holes don't look dirty you don't need to remove them. As far as I can remember it isn't made to be taken apart.

  • Like 1
Link to comment
Share on other sites
wls1971 Distinguished Member

wls1971

Posted
Posted (edited)

I have seen youtube videos on removal the only one I can find is this but I have seen another that had a better solution than this but cant find it now,

Reinserting would be a reversal of the process above, I think in this video the screw he uses is too long and risks damaging the hairspring the other video I once found was a american guy who had used a similar method but he had made a tool for the purpose that looked better than this solution but I cant find it. I think you could do something along these lines with a bit of care.

Edited by wls1971
  • Like 2
  • Thanks 1
Link to comment
Share on other sites
szbalogh Super WRT Addict

szbalogh

Posted
  • Author
Posted
6 hours ago, wls1971 said:

I have seen youtube videos on removal the only one I can find is this but I have seen another that had a better solution than this but cant find it now.

This is sooo cool! Thank You very much! 

 

7 hours ago, oldhippy said:

Why did you remove the hairspring from the balance cock? You should have just removed the end stones to clean the balance holes, also if you have a good watch cleaning machine and the holes don't look dirty you don't need to remove them. As far as I can remember it isn't made to be taken apart.

Ah i wanted to clean the balanve pivots with that pin polisher rubber. 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      I did that also for a few movements - well, mainly in/around the train jewels. I made big efforts to epilame the mainplate WITHOUT getting Epilame into the Pallet fork jewels (where it's not supposed to be, right?). I made litte barriers with Rodico around that jewel and used drops from a syringe to apply on the rest.  However, I've now stopped doing this. For three reasons: 1. It's a hassle and consumes more of this liquid gold. 2. I didn't see the need when using HP1000/HP1300 lubricants and grease for most part. The two places where I'd use 9010 (i.e. escape wheel and balance) receive Epilame in specific places... or the cap-jewel-setting of the balance suspends the oil sufficiently be capillary action (see my "conflict" about using Epilame on the balance jewels).  3. Lastly, and here I really wonder about yours and others' experiences: I felt that applying Epliame to the train jewels left them looking hazy (borderline dirty) compared to the (painstakingly achieved) sparkly clean results of my cleaning process. I just can't help but think that the Epilame residuals would mix with the oil and cause more friction/wear. I don't know.    simple: it'll stay there. It won't move any further. That's exactly what is happening if you epilame a cap stone. You end up placing the 9010 right on top of the epilame and the oil will sit nicely on that spot.
    • Neverenoughwatches
      Coil for old Seiko Credor -- 4002920

      By Neverenoughwatches · Posted

      There are some parts on Ebay for the seiko 6020A, it may just be a waiting game for someone to strip one down, NOS will be more scarce . K would strip your movement down to the module then start looking at other seiko movement to see if that coil is used, then seek out a seiko part dealer. Also Retrowatches youtube owner Mike may give you some advice try him on his site . He also hangs around amateur watchmaking groups.
    • Waggy
      Setting lever spring

      By Waggy · Posted

      I would agree, in order to work harden something you need to exceed it's yield strength when it moves from the elastic zone to the plastic zone and you get permanent deformation and work hardening which is fairly close to its failure point, relatively speaking and dependent on the material/alloy of course. In theory you can load something constantly within its elastic range and not suffer work hardening issues.
    • Waggy
      Coil for old Seiko Credor -- 4002920

      By Waggy · Posted

      Probably easier to get a complete new movement - but CousinsUK list it as discontinued. Maybe someone on here knows a substitute movement ?
    • Kkramme
      Coil for old Seiko Credor -- 4002920

      By Kkramme · Posted

      Any other thoughts on how I can get a replacement coil? Any “hidden” or unknown physical shops (in Australia or elsewhere) that might have them in stock (but not always online)?
×
×
  • Create New...