Jump to content

Recommended Posts

Posted (edited)

I had sold this watch to a collector here on Oahu , Hawaii , and he put some money down on it with the intention of paying off the rest in a short period of time . Unfortunately the buyer became burdened with other financial obligations and after a couple of months I returned his down payment and this baby is all mine again .

From what I have read and using the serial # , it is a 1964 Model with the AS 1700 / 01 movement . I have had the back off and the movement is very clean with no signs of corrosion , scratches , or dirt . There are no markings from watchmakers and there is a Glycine Hallmark on the inner case back .

It is an Automatic with the distinctive internal wire used for the hacking . All functions of the watch work properly and it keeps good time . It has a 24 hour movement instead of the usual 12 hour movement found in most watches . I used to think that the crown had been changed because it did not have the cross hatch design on it , but after some reading I found out that that feature was introduced the following year ,...1965 .  Mine has the red date wheel that was changed to black in the early 60's , but I also read that various configurations come up in regards to dial markings  and other features during this transformation period .

All I have done to it is install a canvas top / cordura underside watch band reminiscent to those sold during that period . I also installed a crystal with the trapezoid magnifier , and repaint the bezel numbers .

 

DSC00054.JPG

DSC00055.JPG

DSC00056.JPG

DSC00060.JPG

 

http://andres55.home.xs4all.nl/frames/airman25years.htm

http://www.glycintennial.com/serial-no.---calibers.html

Edited by ricardopalamino
  • Like 5

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • I believe @nickelsilver has a setup like that.
    • I posted pictures earlier in this thread. My lathe and mill are two separate instruments. I think I have seen examples of putting a milling head on a lathe bed...but not certain.
    • Timex Camper, September 1994, new to me. Strap is an old perlon with "Germany" in script etched into the resin on the tail end. Not Horlon or Eulit I believe. History unknown, running strong, losing less than a minute a day. Goals for this: Wear it a ton! Buy crystal lift, clean out the gunk around the ring and under the crystal Eventually swap into a stainless steel case. I've seen a member who has swapped a Timex mechanical movement into the Timex J.Crew quartz field watch case.
    • One of the problems we would have with a watchmaker's lathe is they were made over considerable span of time and manufacturing in the early days probably wasn't as good as it was today. Then if you look at the older catalogs typically it was just the head a few collets and something to rest graver on. So basically a basic lathe with over time things acquired but acquired things may or may not fit. Order today you purchase a used lathe that all kinds of nifty bits and pieces from a seller that acquired from? This would come back to that the basic watchmaker's lathe was used for basic watchmaking like turning things with a hand graver. Then limited indexing is fine because you can make things like stems Which don't need a whole bunch indexing   In the link above the word vector is mentioned and at the link below you can purchase one. Then of course you're going to need the motor that's a little bit extra for the price. https://www.hswalsh.com/product/lathe-vector-watchmakers-48-collets-hl11. That you're going to need some bonus parts like these found this picture online show the classic way of classic gear cutting.   The lathe could have a much bigger indexing disk but it has to be mounted close to the edge. Otherwise you're going to have a whole bunch of smaller disks like this which I think has notches rather than holes. Then as wonderful as these pictures look actually cutting a gear with this is not entirely fun. Look at all is belts all pulling on things and this is a watchmaker's lathe lightweight with lots of bits and pieces attached. It would make more sense if you actually cut a gear with something like this and it tends to be it's not really the best way to do it looks nice on paper but it is not the best way to go. Reality for cutting watch parts would be a bigger machine is much better. Than getting rid of all those belts and pulleys also good. Here is an interesting channel I would've liked of found a different video but this was nice and short if you look at his video as he uses a stepping motor and worm gear assembly for the indexing plate. In this particular video it gets attached to the lathe at about one minute and seven seconds and it looks like it's hiding looks like he has a Sherline. I do know he's had other stuff you'll just have to go through his videos to find it. Then at about one minute and 22 seconds you find out if you set up things appropriately. It's always bad we end up with half a tooth at the very end. Then you will note big lathe yes he's getting a big gear but you could easily cut a watch gear with the setup. And it definitely way more stable than a watchmaker's lathe.         Oh here's a company they been in business since 1911 http://www.fwderbyshireinc.com/  
    • Hello and welcome from Leeds, England. 
×
×
  • Create New...