Jump to content

To Those of you with CousinsUK Tubed Daylight lamps

SSTEEL

By SSTEEL
in Tools & Equipment

 Share

Recommended Posts

SSTEEL Distinguished Member

SSTEEL

Posted
Posted (edited)

Have any of you come across problems with the wiring of these three tubed daylight lamps?  I have two, and a little while ago one of the tubes went out on one of them, and then this morning, a tube went out on my second one.  I had originally purchased some new tubes from cousins, but upon fitting it in the first lamp, it didn't work, so tried a known working tube in the slot, and nothing, so a faulty wiring was suspect.

Fast forward to this morning, back at work, and set about renewing the tube in my second lamp, but low and behold, its another dud, new tube won't work, or known working tube swapped across to the slot the tube wasn't working.  So obviously a faulty batch of these lamps, or a common problem?

I will be ordering those LED lamps that Mark has soon, as I've never been quite happy with the heat these tubes give off anyways.

Just to note, my lamps are almost 4 years old.

Edited by SSTEEL
Link to comment
Share on other sites
bobm12 Distinguished Member

bobm12

Posted
Posted

Sorry to hear that Micky. From what you are saying, it seems to be the wiring. Maybe after 4 years the insulation went boom...I'm glad you found this fault and now everybody reading this knows better.

I hope someone can also enlighten us about this problem.

Cheers,

Bob

Link to comment
Share on other sites
SSTEEL Distinguished Member

SSTEEL

Posted
  • Author
Posted

I just looked through my paperwork for these lamps, and now realise, the first lamp I got was from eBay, its exactly the same as the ones Cousins sell.  I read my notes that I contacted the seller at the time about the problem, and they said to return the lamp back to them, and they would replace for free, however I was so busy at the time, I put up with it, and ordered a second lamp from cousins.

Now the cousins lamp has done the same, it has to be a manufacture QC problem in my opinion, both lamps have the same markings, made in China etc, so no doubt from the same supplier.

Link to comment
Share on other sites
lluvitar Member

lluvitar

Posted
Posted

Sounds like they have you between a rock and a hard place SSTEEL.  <grin>

 

On a lamp related question.  Which lamp(s) does Mark use?  I bought a LED lamp off Amazon that is okay for light output but it comes from a rather small area.  So the light is easy blocked by head, hands or tools.  Just curious if you knew the specific lamp Mark is using or you had found something similar.  

  • Like 1
Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

I remember HSwalsh from my days, never heard of the others.

I used to go to Mahoney associates.

58 Stapleton Road

BS5 0RB Bristol

City Of Bristol England

0117 955 6800

 

i don't know if there still going it was a family concern and they where excellent.

The other was Southern Watch and Clock Suppliers Orpington Kent

 

Link to comment
Share on other sites
SSTEEL Distinguished Member

SSTEEL

Posted
  • Author
Posted
38 minutes ago, lluvitar said:

Sounds like they have you between a rock and a hard place SSTEEL.  <grin>

 

On a lamp related question.  Which lamp(s) does Mark use?  I bought a LED lamp off Amazon that is okay for light output but it comes from a rather small area.  So the light is easy blocked by head, hands or tools.  Just curious if you knew the specific lamp Mark is using or you had found something similar.  

Mark has posted about the led lamps, they were from cousins too.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Hey from North Carolina

      By oldhippy · Posted

      Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.  This might be helpful for you.  704789946_TZIllustratedGlossary(2).pdf
    • Michael1962
      404 Club

      By Michael1962 · Posted

      I take it that you're comment re the Unicorn is 'tongue-in-cheek'? Would any of the watches that are on the link I posted be likely to be radium watches? What period was that prevalent in and when did the practice stop?
    • Michael1962
      Without Our Forum

      By Michael1962 · Posted

      As much as I hate Facebook, can a forum-like place be set up on there? Free and the ownership can be taken over by the next person whenever.
    • HectorLooi
      Mechatronics Engineering v Mechanical Engineering

      By HectorLooi · Posted

      I existed before the term mechatronics engineer existed. I had to combine electricity, electronics, pneumatics, hydraulics and computing just to keep my own equipment working. I have never sub contracted any of my own repairs to the suppliers because I know I could do a better job. For a long time, dental suppliers in my country would bring their dead equipment to me that their own engineers cannot handle. I have accidentally embarrassed a couple of hospital heads of engineering by demonstrating their inadequacy.  I think mechatronics is the most under-appreciated, under valued of all the engineering sciences. I had a part-time dental assistant about 25 years ago, who was studying mechatronics in the polytechnic. She was absolutely clueless about the job prospects for a mechatronics engineer. I asked her about her aspirations and she replied that she really wanted to work in the games industry.  In our dental profession, equipment have evolved from simple mechanical to electro-mechanical to logic-driven electro-mechanical and currently to computer driven machines.  The medical equipment suppliers who employ mechanical engineers and/or mechanical engineers cannot cope with the repairs of the newer equipment. And many times end up changing whole modules and whole machines just because they cannot repair them. But I think HR is afraid to employ a mechatronics engineer just because they don't know what a mechatronics engineer does. Mechatronics is much more fun. It combines almost all of the engineering sciences and produces an all-rounded engineer. But until HR changes their mindset, not all door will be open.
    • CYCLOPS
      Hey from North Carolina

      By CYCLOPS · Posted

      Welcome Tarheel, there is a lot of help on this forum...
×
×
  • Create New...