Jump to content

problem with seiko 7s26

ramrod

By ramrod
in Watch Repairs Help & Advice

 Share

Recommended Posts

ramrod Super WRT Addict

ramrod

Posted
Posted

i have a seiko 7s26 that i have used to make a rather nice pilot watch. i can't remember where the movement came from. it runs all day long while it is dial down. but, when i flip it over, such as would be worn on your wrist, it slows and stops almost immediately.

i have not taken this movement apart, but when i do, what should i look for?

WileyDave WRT Addict

WileyDave

Posted
Posted

guessing, but i'd say balance assembly or pallet/jewels incabloc, dirty, cracked, worn or bent pivot(s), too much endshake or not enough, seen this on pocket watches, takes a pretty hard knock to get Seikos out of whack, balance staffs and roller jewels are usually robust unless they are dirty. hope that helps

  • Like 1
rogart63 Distinguished Member

rogart63

Posted
Posted

Look for wear in the train wheel bridge and movement plate? Where the arbor is. That is a place where Seiko is usually worn. To much movement and the barrel will lock when you have the movement in different positions?

  • Like 1
ramrod Super WRT Addict

ramrod

Posted
  • Author
Posted

well, i have narrowed it down by accident. i swapped the balance into an NH35 movement that i have also. the thing took off running immediately. it ran all night in the inverted position, but when i turned it over, it stopped.

so, it looks like the balance is dodgy. i'll pull it and look for a pivot to be damaged. this might be the solution.

 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • TimeWerks
      Omega sweep second pinion friction spring - correct tension IS important

      By TimeWerks · Posted

      Thanks for this post MikePilk, I just came across a similar problem with an Omega 1022.  The problem I had was the seconds pinion spring was bent out of shape and did not even engage with the wheel properly, so the seconds hand was not moving at all. (no power loss though :) I removed the automatic module so I could access the spring and work on it. Once I bent it back close to the right shape, I experienced the same problem you reported about power loss.  Many tweaks later, and the seconds hand is moving properly again, with amplitude back to good numbers again. Cheers
    • caseback
      Clock newbie

      By caseback · Posted

      After cleaning up the pivots, I made bushes on the lathe. At this point I've pressed in 6 bushes (3 sets) and the wheels turn smooth. What I can also tell you, is that I'm not looking forward to final assembly. Getting the pivots aligned seems to get exponentially more difficult with each wheel that is added.
    • JohnR725
      Greetings from Whidbey Island.

      By JohnR725 · Posted

      Islands are interesting places to live depending upon their size and other factors. This is a bigger island and it has a bridge to get there at least on one end. It's also big enough that you don't have to go someplace else to get things typically. It can be a problem if you get a job in Seattle though. Yes I've known of people who commuted from the island to Seattle for a job and I don't quite remember how many hours it took but it took a long time. So basically islands are nice if you don't have to leave very often.
    • VWatchie
      What's your thoughts on this Rolex Sea-Dweller, ref. 16600, calibre 3135 project?

      By VWatchie · Posted

      Thanks @JohnR725! Everything you say makes a lot of sense and is encouraging to read.
    • JohnR725
      What's your thoughts on this Rolex Sea-Dweller, ref. 16600, calibre 3135 project?

      By JohnR725 · Posted

      isn't it nice to have a decent case open or when the case doesn't want to be opened? In the case of a Rolex watch that supposed to pass specific water resistant testing you probably do need to tighten the back down. But they shouldn't be tightened so much that they risk stripping the threads out. Then the other problem that comes up is the gaskets can start to disintegrate and then getting the back off can be quite a challenge unless you have a really good tool and perhaps some penetrating oil to loosen things up. Yes really nice case marking. When I was in school we were taught to mark the cases and  the American watch and clockmakers Institute even had a? So if you joined at one time they would give you an identification number. They were explaining or giving an example of if the watches ever found in you have a unique number they can perhaps figure out the history of the watch or identify the body it's attached to for instance not that that probably comes up that often. So you got a unique number and even made a special metal stamp that you can purchase. It wasn't a super big aggressive stamp but still it left a mark in the back of the case. Then I heard from people at work on Rolex watches they were using a felt pen indelible but later on they decided that was bad because apparently the ink could release  chemicals although it seems like once it's dry that shouldn't be an issue. Then of course today was nice is you can keep computer records sealed have to mark anything at all I personally find it's best to leave no reference behind that you were even there. Especially when you have a beautiful watch that has no markings at all and now it has your scribbling all over it not good typically if there is a typical and watch repair?  a lot of minor repairs you don't need to do a complete servicing. But beyond a certain point you're going to have to take apart a lot of stuff you're going to disrupt the lubrication even if it looks perfect right now and yes you might as well just go ahead the service the whole thing. also in a watch like this where a lot of things seem to be going on the complete service would be better then you'll know exactly where you stand versus dealing with unknown mysteries for prior repair.
×
×
  • Create New...