Jump to content

Balance Tack- Small Project

steve855

By steve855
in Tools & Equipment

 Share

Recommended Posts

steve855 Watch Enthusiast

steve855

Posted
Posted

Hello All,

I haven't posted much lately because I haven't really done much lately. I had some free time this past weekend so I spent it in my workshop. A balance tack is a traditional lathe project and I needed one, so I figured I'd give it a try. The base is 7075 aluminum alloy because that's what I had on hand in the desired diameter. The black transition piece is black acetal, and the tapered shaft is brass. I wanted this to be easy to disassemble so it would fit in a shallow drawer, so the acetal piece has a 0.187" stub on the bottom that's a snug slip-fit with a corresponding hole in the center of the base. The brass portion is a press fit into the acetal. The perlage/spotting on the base was just for fun. Looking at the photos, I could have spent a bit more effort on smoothing the brass taper, but I ran out of time. Sometimes I have more fun making and modifying tools than actually repairing watches. Probably because the tools are not so small!

Thanks for looking

Steve

846e46976ebad4376102228c413f949f.jpg

a4feb25f97be2e7e15d48b2ebbb85705.jpg

55c2de0b3f4bbcd773e5cc787af250bd.jpg

  • Like 7
Link to comment
Share on other sites
steve855 Watch Enthusiast

steve855

Posted
  • Author
Posted (edited)

Marc- thanks, the perlage was actually not difficult. The base has a through hole in the center, I setup a pin this diameter in the drill vise with a crude paper washer slipped over it. The base was then slipped over this, allowing it to be rotated manually around the centering pin. I chucked a pencil eraser in the drill and spun it at moderate rpm, maybe 400-500.

I brushed a small amount of lapping compound onto the top surface of the base then started the first outer row of overlapping circles. With each circle I rotated the base by 1/2 eraser diameter, when the outer row was complete I moved the whole assembly over 1/2 dia with the Y axis and repeated this process until it was finished. It was fun watching the pattern appear, and no special equipment required, other than the mill/drill. I'll try to find a photo of this.

Geo- thank you, I don't have a dedicated watch workspace, so I keep all of my tools in a nice old Gerstner machinist's chest, and most of the drawers are shallow, so the ability to disassemble was important for me.

Edit- photo added

4f40bb4f351756002678681b84e9a8f4.jpg

Edited by steve855
  • Like 5
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      So leave off the seconds. Stand the movement on its edge, its the dial edge that rests on the pad ( either rubber or cork , something that wont slip ). Use a finger of your left hand to hold the movement upright,  right hand presses the release and flicks out the stem. I do it this way so i can see what I'm under a microscope. But you could hold the movement between two fingers of your left hand, its the right that has to manipulate the stem out by pushing the release and flicking out the stem with  right ring finger nail. Sounds more complicated than it actually is. I guess you could fix a push pin to something solid, then all you need to do is push the release against the pin, leaving your right hand completely free to pull the stem out.
    • HectorLooi
      Battery

      By HectorLooi · Posted

      Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
    • Murks
      Battery

      By Murks · Posted

      A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      I think what peter means oh is once he has fitted the hands and  checked for  alignment if them and that they dont foul, how does he then hold the movement to remove the stem in order to case up. The dial cannot be laid on a cushion or in a movement holder as the hands will get damaged. This can be quite tricky for a beginner, what i do is  to stand the movement on edge on a rubber pad so it doesn't slip. Hold the top edge with one finger then my dominant hand uses 3 fingers to press the stem release and flick out the stem. See below peter, leave off the second hand as this is the longest and gets caught the most, then fit it once the stem is out. Alternatively place the movement in one of the cup style holders, i imagine this is what they are designed for. They only touch the very edge of the dial.  
×
×
  • Create New...