Jump to content

Help With Tudor 2671 Winding Stem Removal

suparobg
 Share

Recommended Posts

suparobg Watch Enthusiast

suparobg

Posted
Posted

I have attatched a picture or 2 is there a screw on this movement or a button type release on this 2671 Tudor Princess Date movement

I need to remove the stem.

Let me know the steps to take and how it should be prepped.

Thanks

post-144-0-94268700-1396536776_thumb.jpg

post-144-0-90017900-1396536778_thumb.jpg

Link to comment
Share on other sites
suparobg Watch Enthusiast

suparobg

Posted
  • Author
Posted

any idea how far to push it in, I hear that some movements if you push down to far it might mess things up. Sorry I'm not technical when it comes to the wording. Just the basics like crown,crystal,stem, rotor etc.

i will give that a try

thanks

Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
Posted

I'm sure others who have done this more than I will give you direction...

 

But, From what I can remember, use a screw driver about the same width as the slot to push the pin in. You don't want to push the pin is farther than the slot shoulders will allow as this will cause the retaining pin to slip out of place. Then it may require disassembly to replace the retaining mechanism

  • Like 1
Link to comment
Share on other sites
Lee WRT Addict

Lee

Posted
Posted

just don't push it in when you refit the stem, you should be able to turn it back into the movement without touching the button, its often when you put the stem back in you get problems with it disappearing (if you push it)

Link to comment
Share on other sites
suparobg Watch Enthusiast

suparobg

Posted
  • Author
Posted

I got it out but now I can't seem to get the movement straight into the case. I had to remove one case clamp and screw on one side to get the movement to slip in level now not sure how to put back the case clamp. Wish there was some sort of video on the removal and replacement of the 2671 Tudor movement.

I will keep looking to try and figure it out. This is my first time. The watch came with the movement out of the case so it could be called watch parts for customs reasons. Now just have to put it back together.

post-144-0-72319900-1396540381_thumb.jpg

Link to comment
Share on other sites
DJW Super WRT Addict

DJW

Posted
Posted

I don't think that is even the right clip for this application(?) I would guess it should look just live the other retaining clip on the other side of the movement.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • aac58
      Rare Seiko 5actus Watch??!! With a lot🤪🤔😲

      By aac58 · Posted

      This is not rare at all, the dial code and case code don't usually match.
    • Kkramme
      Coil for old Seiko Credor -- 4002920

      By Kkramme · Posted

      Good question!! Anyone know of a substitute movement??!! 🤔🙏
    • Kkramme
      Rare Seiko 5actus Watch??!! With a lot🤪🤔😲

      By Kkramme · Posted

      Interesting issue that I just noticed: this Seiko 5actus Watch from 1977 has a calibre listing on the dial of 7019-8030R but on the case back it says 7019-8010!! Like a mis-printed coin, is this watch therefore worth a lot of money for its rarity?? 🤪😲🤔🤪
    • Mercurial
      Smit

      By Mercurial · Posted

      I wish that was the case. The Aegler movements used in the early days by Wilsdorf & Davis (for brands like Rolex and Rolco) came in several sizes and without designated calibre numbers that survive.  They become a bit easier to identify during the 1920s. Below is an Aegler-Rebberg, 25.74mm in diameter. It’s from a woman’s Rolex wristwatch. Stamped Rebberg and 500 on the dial plate (but it isn’t a Rebberg 500, it’s the wrong size).  I’d be interested if anyone can identify the movement.  It is based off the Aegler Nr.1, circa 1903, but they based many many calibres of different sizes on it. The closest I have to a positive ID is the  ‘Rolex Nr.50’ circa 1917, but no dial side images or movement sizes are available in the references. There are identical looking movements in many sizes.  The 25.74mm of this movement is a particularly strange size for the era, it equates to 11.41 lignes.      Best Regards, Mark
    • GuyMontag
      FHF70 balance jewels settings

      By GuyMontag · Posted

      It looks like this movement comes with a number of different shock settings. Emmywatch shows that it comes in versions with no shock settings, 'Incabloc', 'shock resist', and 'Supershock'. Perhaps the different settings position the impulse jewel/roller table in a non-ideal position relative to the pallet fork/guard pin. Are you able to check under high magnification if the pallet fork and roller table are able to operate without any interference? Just for fun I took a look and I have one FHF 70 in my collection, a West End Secundus with a non-shock protected FHF70. I had a note with the watch that said, "Movement is stamped 'FHF 70', but the FHF70 looks to have sub-seconds instead of center seconds movement (??)" but that a google search turned up both types for this movement. EDIT: I just took a look in my parts drawer and I have a few of these movements, both in center seconds and sweep seconds, but they all are non-shock protected.  
×
×
  • Create New...