Jump to content

Gucci 9300 Chrono Instruction Manual

watchmad

By watchmad
in Watch Repairs Help & Advice

 Share

Recommended Posts

watchmad Member

watchmad

Posted
Posted

I'm looking for any instructions for this watch to reset everything after a battery change.

It's some complex series of presses on the 3 pushers and 1 crown but I can't remember the sequence and I've lost the instruction sheet that I had.

Any help would be appreciated  :geek:

post-1589-0-67837200-1447735313_thumb.jp

  • Like 1
Link to comment
Share on other sites
watchmad Member

watchmad

Posted
  • Author
Posted

Thanks guys.

Yeah it doesn't seem to work using those instructions.

The movement is Swiss with 1 battery for the time and another battery for the Chrono functions.

I found a picture of the movement here: http://www.watchrepairtalk.com/topic/1112-gucci-9300/

I seem to recall having to press 2 buttons simulateously while the crown is out but I can't recall exactly.

Link to comment
Share on other sites
watchmad Member

watchmad

Posted
  • Author
Posted

I even sent an email to Ronda in Switzerland but got a fairly unhelpful reply..   but at least they did reply:

 

According your description we don’t have/had such movement in our sales program. But we know, that some of our clients added RONDA watches on their modules, which they have assembled to entire watches.

So in this case we know only the functions concerning the time indication. Please contact the watch brand (Gucci) for further instructions.

Link to comment
Share on other sites
watchmad Member

watchmad

Posted
  • Author
Posted

Unfortunately not.

The watch has 3 pushers and 1 crown and as near as I can tell, the crown only has 2 positions.

It has been many years since I had a battery in this watch but I seem to recall needing to press some obscure combination of the pushers after changing the battery.

Link to comment
Share on other sites
  • 11 months later...
Seiko7A38 Member

Seiko7A38

Posted
Posted
On 11/17/2015 at 6:36 AM, Geo said:

Welcome to the forum Watchmad. I suspect this may have a Seiko 7a28 movement in it, so try setting it using these instructions.

image.jpeg

George.

I did spot this (incorrect) post of yours earlier and I had to chuckle to myself. :biggrin:

It's an easy mistake to make with these 7Axx clones, of which the Gucci quartz chono's are just one. There are other bone fide brands of 7A28, the most obvious being Yema, which use a (re-branded) Shimauchi Ltd V905 movement. The easy way to tell a 7Axx clone from the 'real deal' (without sight of the movement) is to check the increments on the LH minute counting sub-dial. Usually they'll go up to 60, whereas a pukka 7Axx only counts to 30 minutes. Plus they're usually 'Swiss Made'. <_<

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HectorLooi
      Battery

      By HectorLooi · Posted

      Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
    • Murks
      Battery

      By Murks · Posted

      A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      I think what peter means oh is once he has fitted the hands and  checked for  alignment if them and that they dont foul, how does he then hold the movement to remove the stem in order to case up. The dial cannot be laid on a cushion or in a movement holder as the hands will get damaged. This can be quite tricky for a beginner, what i do is  to stand the movement on edge on a rubber pad so it doesn't slip. Hold the top edge with one finger then my dominant hand uses 3 fingers to press the stem release and flick out the stem. See below peter, leave off the second hand as this is the longest and gets caught the most, then fit it once the stem is out. Alternatively place the movement in one of the cup style holders, i imagine this is what they are designed for. They only touch the very edge of the dial.  
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes I understand that. What I’m asking is, after the hands have been fitted, it’s been checked that the hands do not touch etc. then I need to remove the stem to fit the movement in the case. I have the push type, I need to turn it upside down and push the setting lever post and pull the stem out. But of course the dial and hands are in place and I have a glossy dial with lume dots and I do not want to cause any damage while it’s upside down pushing on the post of the setting lever.
×
×
  • Create New...