Jump to content

In Absentia

atimegoneby
 Share

Recommended Posts

  • 2 weeks later...
oldhippy Distinguished Member

oldhippy

Posted
Posted

Very nice but like George says it's tidy. Now I don't mind admitting my old work bench had stuff all over the place in fact it was absolutely filthy, people would come into my work shop and remark how untidy I used to be, my answer to them was I new where everything was.

Link to comment
Share on other sites
  • 3 weeks later...
Vich Distinguished Member

Vich

Posted
Posted

I thought the rules said that everything on the desk had to be covered with horological paraphanalia and bits and bobs generally except of course about a square foot in the middle reserved for actual working.  Natty electric blue loupe though - want one.   like our Bob says, you could have put a watch on the desk though instead of that digital clock (which incidentally will be a constant reminder that there are other jobs in the house to do instead of hobbying).  Don't know what bike that is but I bet George has one.

 

Seriously, good that you are back and hope the sorting out gets completed without too much strife.

 

Vic

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Neverenoughwatches
      Questions about my Bravingtons Renown Mantel Clock

      By Neverenoughwatches · Posted

      Hmmm you know when i said some damp might have caused the bubble originally hmmm.
    • Neverenoughwatches
      404 Club Reboot

      By Neverenoughwatches · Posted

      Are you all jerking my chain, I'm a yorkshireman £4.04 is too much 😆
    • Kkramme
      Blew it with a coil

      By Kkramme · Posted

      [Myota2034] Custom simple quartz watch — PricewaterhouseCoopers On a very very different note, here is a watch from approximately 2000 when I was a Partner with PwC, Management Consulting. It was a simple “marketing watch” with a clever “vase of knowledge” that is subtly revealed on the dial as the second hand progresses. Clever for a simple watch!⌚️
    • Neverenoughwatches
      Mainspring winder question.

      By Neverenoughwatches · Posted

      I think someone else has though. Some where here using a modified perspex sheet. I may be wrong i may be right , i think it involved fitting the arbor to a pin vice. I dont have experience of the bergeon winders, are the handles not interchangeable ?
    • Neverenoughwatches
      Dial Dots

      By Neverenoughwatches · Posted

      Never tried dial dots, i always considered them as a bit of a bodge.  You are adding something that was never intended to be there. I wonder how the adhesive reacts to any part of the movement, hot summer heat and i think things might turn sticky. Most adhesive backed stuff has a tendency to soften and slide around so it may spread, i have used a lot of so called sticks all adhesives in my industry that are just not up to the job. I suppose they get you out of a problem quickly, but how permanently might that be ? I would just explain to the owner that it may or may not work. WWs other ideas are a much more permanent solution but both have their risks . I've tried milling and dial feet replacements, hmm it was ok, ive heard of folk dimpling the face , so that needs care . And i have soldered a few times , all with good results but i am very careful and I practiced it a lot.
×
×
  • Create New...