Jump to content

Rotary tool

ClaudioCavalli
 Share

Recommended Posts

ClaudioCavalli New Member

ClaudioCavalli

Posted
Posted

The next tool on my list is a rotary tool to fix a couple of scratched up crystals.  I've been reading up on watch forums on what tool people use and I see a lot of people use Dremel and Proxxon rotary tools (Did you guys see their mini lathes?  Wow!!).  However, I see that their minimum speeds are 2,000 rpm or so.  Isn't this too much for polishing?  No room for error?  I was looking at something like a Grobet rotary rool (See here) but they do not have specs for lowest speed on their web site.  However, similar tools on Amazon go down to 500 rpm.  Does anybody know if the Grobet goes down to 500 rpm as well?  Wouldn't this speed be better and more forgiving for polishing plexiglass crystals?

thank you

claudio

Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
Posted

The Chinese made motors are pretty good too. I've been using one for the last 6 months. 

I think the electronic foot pedals for sewing machines may work as a substitute but it would require a bit of rewiring. The problem with the Chinese Foredom pedal is that the potentiometer has a very short travel of about 1 cm only. The sewing machine pedal has a potentiometer at least twice as long.

Flexshaft motors can go down to quite a low speed but it wouldn't have much torque at these speeds.

Polishing is a lot of trial and error. The required speed depends on the material being polished, the polishing compound used and the type of polishing tool used. (eg. Silicone rubber abrasives, soft felt, hard felt, wool mop, muslin mop, etc)

The amount of pressure used also depends on the above variables. Some require high pressure, others require a light touch.

It's a science as well as an art. Have fun! 😉

Link to comment
Share on other sites
  • 3 weeks later...
VWatchie Distinguished Member

VWatchie

Posted
Posted
On 12/26/2023 at 5:41 AM, ClaudioCavalli said:

I've been reading up on watch forums on what tool people use and I see a lot of people use Dremel and Proxxon rotary tools (Did you guys see their mini lathes?  Wow!!).

I haven't had the best of experiences with a rotary tool for polishing.

I've had a lot more success using a dedicated polishing machine so I'd recommend that.

 

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • mikepilk
      AS 1475 REFURBISH (Recalled to life)

      By mikepilk · Posted

      I've just finished refurbishing a Memostar Alarm with AS 1931 movement (same as 1945 but with date and running at 21600). I was also surprised how many parts are available at Cousins. Like you, I was missing the alarm stem (Cousins stock them) and I needed new crowns. It's a nice simple movement for an alarm, easier to service than a Seiko Bell-Matic. BTW I made a note in my Servicing spreadsheet: "Pull out winding stem before removal".  It may have just been wear on my movement, but I found that the yoke could move out of the clutch if the stem was removed in the normal position (like some ETAs).  You might find this interesting     
    • LittleWatchShop
      AS 1475 REFURBISH (Recalled to life)

      By LittleWatchShop · Posted

      I picked up this alarm watch at a flea market several months ago and recently decided to investigate.  I am not finished, but well on my way. As you can see, there was significant water damage.  Running these parts through my L&R cleaner was not enough to clean them, so I did manual cleaning with one-dip and cotton swab (the dense pointed kind).  The wig-wag was stubborn--the two gears would not release from the plate.  I soaked it in Kroil overnight and that did the trick. There was some rust on the balance staff, but not actually on the pivots themselves.  Nevertheless, I chucked it a step-chuck on my lathe and burnished the pivots. The watch is running and I have confirmed that the alarm drive train is functioning.  Since I am missing a stem for the alarm, I have not done the final assemble of the alarm components.  Surprisingly, there are lots of parts available for this movement on Cousins.  I will probably get a couple of stems and maybe some other parts that I deem necessary. The watch is running at weak amplitude (about 190) and shows some poising issues.  I will work on that. The last two pictures are after partial reassembly.    
    • watchweasol
      Greetings from India.

      By watchweasol · Posted

      Hello and welcome to the forum.    Enjoy
    • Knebo
      DIY centre seconds support base

      By Knebo · Posted

      Exactly!  It may not really be a joke, but the actual truth.
    • HectorLooi
      DIY centre seconds support base

      By HectorLooi · Posted

      The movement is placed on the base and the centre screw is raised until it contacts and supports the centre pinion, thus stopping the centre pinion from sinking in when the second hand is pressed on.
×
×
  • Create New...