Jump to content

Question about repeater watches

Jaime
 Share

Recommended Posts

Jaime New Member

Jaime

Posted
Posted

Hi. I have these 2 repeater (I think quarter) but they are not chiming the correct time. I tried to change the time on one of them to what it was chiming but it changed and was wrong again. Also, on the wind up watch- how do I change the time? Is it by the center of movement. There is only one hole in case for the winder. Thank for any information. On one of them the chimes sound sort of “sickly” like it’s struggling to chime. 

IMG_4368.jpeg

IMG_4369.jpeg

IMG_4371.jpeg

IMG_4372.jpeg

oldhippy Distinguished Member

oldhippy

Posted
Posted

Both are very delicate. The first one someone has bent the minute hand. The second one to change the time its the center square. You must change the time by letting the watch chime and strike each time other wise you might foul up the movement. I expect they both need a good service. These must be repaired by someone who is advanced in repeater work. 

  • Like 1
JohnR725 Distinguished Member

JohnR725

Posted
Posted
2 minutes ago, oldhippy said:

Both are very delicate

this translates into you want to be very careful with these because screwing up things will become very very expensive very very fast.

 

3 hours ago, Jaime said:

Also, on the wind up watch- how do I change the time?

try unscrewing the bezel and see if it's a lever set watch if you can't pull the crown out like a normal watch that you would set.

 

 

 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • donutdan
      Parts sourcing for FHF 180 movement

      By donutdan · Posted

      Hi Watchrepairtalk, I have some questions about part sourcing I was hoping someone here might be able to help with. I'm working on an FHF 180 movement with a broken balance staff, broken regulator pins, and damaged cap jewels (both top and bottom). Some Googling says that this is similar to other FHF calibers like 150s, 160s, 180s and so on but I can't figure out what the functional difference is between these movements.  Is there any reason I wouldn't be able to acquire a donor FHF 150 or similar (with no shock protection) and use parts from that or would it be smarter to source replacements individually? Also are there any sources someone could recommend to get bulk cap jewels like this? Thank you for the help!
    • Nucejoe
      Greetings from Whidbey Island.

      By Nucejoe · Posted

      Hello and welcome to the WRT forum.
    • JohnR725
      A lathe with indexing that won't break the bank?

      By JohnR725 · Posted

      interesting video nice to see the machine what it can do now I wonder what it costs and I'm sure it's not in my budget. Plus the video brought up questions but the website below answers the questions? What was bothering me was the size of his machine 4 mm because I thought it was bigger than that? But then it occurred to me that maybe they had variations it looks like four, seven and 10. With the seven and 10 being the best because way more tool positions in way more rotating tools. Although I bet you all the rotating tools are probably separate cost https://www.tornos.com/en/content/swissnano   Then as we been talking about Sherline. Just so that everyone's aware of this they have another division their industrial division where you can buy bits and pieces. I have a link below that shows that just in case you don't want to have the entire machine you just need bits and pieces. https://www.sherline.com/product-category/industrial-products-division/   Let's see what we can do with the concept I explained up above and bits and pieces. For one thing you can make a really tiny gear very tiny like perhaps you're going to make a watch. Then another version the center part is not separate it is all machined from one piece. Then fills gear cutting machines have gone through multiple of evolutions. A lot of it based on what he wanted to make like he was going to make a watch unfortunately eyesight issues have prevented that. Another reason why you should start projects like this much sooner when your eyesight is really good or perhaps start on watches first and then move the clocks then local we have from the industrial division? Looks like two separate motors and heads. Then it's hard to see but this entire thing is built on top of a much larger milling machine as a larger milling machine gave a very solid platform to build everything.   Then like everything else that had multiple generations are versions the indexing went through of course variations like above is one version and the one below was the last version. Now the version below I mentioned that previously and somewhere in the beginning to discussion and somebody else had one in their picture. As it is a really nice precision indexing. Then I wasn't sure if I had a the watch photos here is his unfinished watch. No he wasn't going to make a simple watch like none of his clocks were simply either what would be the challenge and that.    
    • Titanium
      Lab Coats

      By Titanium · Posted

      Use a Portwest Howie lab coat. They are the biological type so they have tapped cuffs so you don't end up getting the loose cuffs of normal lab coats catching everything. 
    • Titanium
      Chinese tools debate

      By Titanium · Posted

      Some of the Chinese tools ae great and can be purchased at a fraction of the price of Swiss ones, some are complete garbage and some I'm convinced are coming out the same factory as the branded ones.
×
×
  • Create New...