Jump to content

Waltham mass bond st full hunter pocket watch advice needed

Bygone
 Share

Recommended Posts

Bygone New Member

Bygone

Posted
Posted

Hello Everybody !!

Im new to watch repair,I’ve been working on smiths/Enfield style mantle clocks and Anniversary clocks for about three years.

I’ve bought a not working Waltham mass bond st  full hunters pocket watch as my first to work.

ive stripped it down, cleansed ,checked parts and have just installed the keyless works..Now here’s my  first rookie mistake 😂,

when I stripped the watch down,in my nievety or stupidity,which ever one you feel fits(I’ll accept them both😀)..

I’ve taken all of the screws out and I’ve not left the crown pin screw in ,and just turned it quarter turns until the crown pops out.The crown and the crown pin are fixed to the pocketwatch case.

Im ready to move to the next stage of the build now,but I’m not prepared to carry on building it back up until I’m clear in my mind what effects not leaving the screw in has on my rebuild,and indeed a clear way foreward to put right my mistake,which as yet I’m not sure of the way foreward..Any help or advice will be fantastic guys and gals.But be sure I’ll not do it again😀.

Thankyou

 

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Jon
      Breitling Navi Heritage (ETA 2892A2) seconds subdial skippiness...

      By Jon · Posted

      To be honest, they're not a good movement to have in a chronograph for several reasons. The first is the chronograph mechanism is a 'bolt on' module; If you look at the side of the watch case the crown won't be in line with the pushers, therefore only the branded company would have the ability to swap out the module because they aren't designed to be serviced and definitely not by an independent watchmaker. Secondly, the ETA 2892 A2 is a great movement, but when the chrono module is used with it it becomes pants, in my opinion/experience. So, going back to your watch. The problem isn't with the base movement, which is the 2892A2, as there would never be that amount of backlash/flutter in the gear train of that particular movement, it is with the chrono bolt on module that the problem lies and when the chrono sweep second hand is engaged the flutter of the second hand is remedied by the stability of the chronograph mechanism negating that flutter. Everything in the chronograph mechanism of that movement is powered by a wheel in the centre where the cannon pinion/driving wheel would normally be. I think it is a crappy design deliberately engineered to be disposable due to the time taken to service the module. Give me a 7750 any day!
    • Neverenoughwatches
      Citizen Technical Info

      By Neverenoughwatches · Posted

      Yeah not much going on in the town , Scarborough is a bit better,but the missus and me love York. Good antique shops there, The antiques center on stonegate has a good selection of vintage watches, top price though.
    • oldhippy
      Good evening and hello there.

      By oldhippy · Posted

      Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement. 
    • Chief
      Citizen Technical Info

      By Chief · Posted

      Brid isn't what it used to be, I only really go to Morrisons in brid. I avoid the town. But Scarborough is nice! I don't mind a wander round the beach between jobs
    • Simeon
      Orient Automatic Crystal and Bezel

      By Simeon · Posted

      I have had a few issues with my Orient Automatic crystal and bezel. The bezel came off with a case knife and I haven't been able to refit it. Doing a bit of research on here, I think that it is an arrangement where the crystal is snapped over a lip on the caseback and then the bezel is installed over the top like a tension ring. I have managed to crack the crystal trying various attempts to press it onto the case. Measuring the crystal with Vernier calipers, I think it is a Sternkreuz XS 314.171 but I can't correspond that to the reference/ case number on the caseback. I also measured the outer diameter of the lip on the case that it may fit over and this is 30.5mm, which is actually 0.7mm bigger than the static inner diameter. Is it likely that the crystal can be expanded enough to snap over that? The inner diameter of the bezel/ tension ring is 32.2mm which works with 31.4+0.7 = 32.1mm Does this sound correct? What method should I use to snap the crystal and then bezel into place? I have a cheap case back press with nylon dies but I managed to break the old one with this method.       
×
×
  • Create New...