Jump to content

Waltham 8 Day

Davis
 Share

Recommended Posts

Davis Watch Enthusiast

Davis

Posted
Posted

Dissembled, cleaned and reassembled my Waltham 8 day car clock from 1920. Wound the movement and it started but had balance wheel wobble. On close inspection I could see the upper pivot moving in the jewel.  Removed the two screws holding the upper jewel in lace but can't seem to remove the jewel carrier.

Any help in resolving this problem would be appriciated.

Thanks in advance, Dave

IMG_4831.jpeg

Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted

The jewels are usually pressed in gently. This means to get them out means that you have to remove the balance bridge I would remove the balance wheel from the balance bridge when you do this. Then using peg wood push from the backside and both the hole jewel and the end stone and settings will come out. You can't just loosen the screws and pop them out they have to be pushed out gently.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • swiss2k
      Omega cal. 565 - low amplitude

      By swiss2k · Posted

      No matter what I did, I could not get the amplitude more than 240 deg. At least there is 0.2 beat error and minus 1-2 s/d.  So, probably not the happy end I would have hoped for, but still I think the watch turned out quite nice. You be the judge of that. Thank you everyone for your help!  
    • transporter
      First pendulum clock tinker

      By transporter · Posted

      its used to lengthen or shorten the suspension spring from the front f the clock dial, this in turn will give regulation to the clock. Try inserting a pocket watch key or even better the double ended key for the clock into the small aperture on the dial at the top and turning it, you will see the suspension block either raise or lower. If it raises the clock will run faster if it lowers the clock will run slower
    • dnhb
      First pendulum clock tinker

      By dnhb · Posted

      Grateful for info regarding the nature & function of the horizontal cog and the unit it's on top of in the picture. It meshes with a vertical cog (enclosed in the unit) on the arbour which is supported at its other end by the back plate of the dial unit to which it is not quite perpendicular...
    • Murks
      Digital Watch

      By Murks · Posted

      does anyone knows what type of battery this digital Watch takes?  
    • Neverenoughwatches
      Second hand watch market.

      By Neverenoughwatches · Posted

      Hello good watch folk ,I  just fancied a light hearted discussion after my head was starting to spin over Epilame 😅. Specifically I'm meaning the sale of vintage watches, say nothing past the 1980s market. The stuff we see on ebay and other similar sites and found at carboots, curio shops etc. And are  we thinking its reaching a peak volume ?  Younger generations clearing out passed parents and grandparents possessions.  The younger folk are not as sentimental as the old fogies ( I'm now nearly at an age that i used to think was old fogie age ). When might it have started ?  i often wish i discovered the hobby much much sooner when selling your grandfathers pocket watch at a boot sale for a few quid was just a way to offload some tat. And when might it slow down. Thoughts anyone ?
×
×
  • Create New...