Jump to content

Balance wheel not secured to balance staff, what do I need to fix this?

GregG
 Share

Recommended Posts

GregG WRT Addict

GregG

Posted
Posted

I have a balance that has a bent pivot.  I have a Levin pivot polisher, but when I was moving the bow back and forth, I noticed that the impulse pin wasn't moving, but the rim of the balance was moving.  So the rim isn't held securely to the staff.  I am not 100% sure how to fix this issue.  I think I saw a video of it once, and the guy used a staking set with a domed punch to rivet the wheel to the staff.  Can someone clarify what I should do, and/or what staking equipment I'll need?

Thanks

Greg

IMG_20221203_200211.jpg

Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted
13 minutes ago, mikepilk said:

I don't think I've ever managed to straighten a bent pivot (more than a tiny amount),  they've all broken

Normally my experience would agree with yours until I found this tool and so far it's worked quite nice for pivots. It also looks like Bergeron has revised it in some way. I have the PDF attached for describing how the tool works which as I said actually works quite nicely. But there is a limit of what you can do with a bit pivot and because somebody didn't put the staff in right the first place it might be better just to start over.

straightening bent pivot tool.JPG

7135 7136 tool for straightening bent pivots.pdf

  • Thanks 2
Link to comment
Share on other sites
mikepilk Distinguished Member

mikepilk

Posted
Posted (edited)

Interesting read. I can buy a lot of new staffs for the price of one of those. But, I might try the technique of finding a slightly larger jewel hole and bending bit by bit.

Just a thought - any reason why you couldn't anneal the pivot, bend it straight, then harden it again ?

Edited by mikepilk
Link to comment
Share on other sites
nickelsilver Distinguished Member

nickelsilver

Posted
Posted
2 hours ago, mikepilk said:

Interesting read. I can buy a lot of new staffs for the price of one of those. But, I might try the technique of finding a slightly larger jewel hole and bending bit by bit.

Just a thought - any reason why you couldn't anneal the pivot, bend it straight, then harden it again ?

You can do a spot temper, with the staff (or pinion) mounted, but to do a full anneal the steel has to go to critical temperature i.e. red hot then cool slowly. In either case to get back to original hardness will require going red hot again then quenching, then tempering.

 

I love that Seitz tool- as a pivot gage. Don't really like it for straightening pivots. I chuck the part in the lathe and turn the spindle by hand to find the max error, and use Dumont #8 tweezers or well dressed stubby nickel tweezers- that have been heated in an alcohol flame until almost too hot to hold- to coaxe the pivot back.

 

The hot tweezers aren't hot enough to affect the temper, but the heat really does help the metal relax and move. Some pivots are simply bent too far and will never straighten without breaking.

 

Op's staff looks homemade and hokey, it's pretty bent. If it's properly heat treated I wouldn't bet on the pivot getting straight before breaking.

Link to comment
Share on other sites
JohnR725 Distinguished Member

JohnR725

Posted
Posted
5 hours ago, nickelsilver said:

I love that Seitz tool- as a pivot gage. Don't really like it for straightening pivots.

As I already have one of the gauges I don't need it for the gauge aspect. Then I probably don't exactly use it the way they say basically does Buddha balance wheel in look and see if it's leaned and I just gently start pushing it and go to the smaller and smaller holes and so far it seems to work.

5 hours ago, nickelsilver said:

Dumont #8 tweezers or well dressed stubby nickel tweezers- that have been heated in an alcohol flame until almost too hot to hold- to coaxe the pivot back.

Then when I was in school instructor George had tweezers that had pieces of wood attached to them so we can hear them up is hot is they needed to be and he didn't have to burn his fingers and I can't really put it in his lathe or whether he did it. But in any case he was always able to save a pivot but as an instructor I'm sure he got lots of practice.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Trav2004
      Help Identifying movement

      By Trav2004 · Posted

      After a bit further research could it possibly be an AS 970?
    • Bonefixer
      FHF70 balance jewels settings

      By Bonefixer · Posted

      Latest project was a non-running ebay purchase with an FHF70 movement. I stripped and cleaned it, reassembled it, and got it running. So far so good, nothing damaged AFAIK.  I was oiling the top jewel on the balance (the one in the cock) which was a slightly unusual shock setting. I removed the spring (3 leaves) which was part of a chaton holding the cap jewel. This left the hole jewel behind which I retrieved with rodico and then lost it. I was taking it off the rodico, very gently as I thought, with tweezers, and then it just disappeared.  Fast forward a week, I got a donor movement, non-running, with the plan to just take the shock jewel that I’d lost. It was the same movement but had standard incabloc settings, and was steel rather than copper/brass.  I changed the cock and balance complete and it ran, not very well. I switched the lower jewel setting, cleaned and oiled both jewels and the replacement balance. Without the pallet fork the balance swings very nicely with a puff of air. With the fork in place, balance out, it flicks side to side nicely with power in the mainspring.  Put them together and it doesn’t run. The impulse jewel sits in the fork and it stops.      Any suggestions how I proceed? In case you didn’t follow that I have 2 FHF70 movements, nothing broken as far as I can tell, but mixing up the balance wheels and jewel settings results in a non runner. 
    • Neverenoughwatches
      Part swapper to part maker

      By Neverenoughwatches · Posted

      Oh and this almost perfect third wheel pivot and slightly set mainspring  Ah ok yes i see what you mean, good idea. I'll try that if i fluff this one up. The image isn't great quality but i like the idea though.
    • RichardHarris123
      Part swapper to part maker

      By RichardHarris123 · Posted

      Why cut the paper, cut a square around the image and grind to it. 
    • Neverenoughwatches
      Part swapper to part maker

      By Neverenoughwatches · Posted

      I did try that last time Rich , i traced the image from the Bestfit book which is the actual size. But its more difficut to cut the shape from paper than it is to grind the steel to shape. This way is pretty easy and the final shaping is done when fitting the part. There are a couple of things i will do differently next time, clamping the 2 pieces together with a drill press will help to hold while scribing the shape in. This was a bit tricky having only one hole, if using the pins and cork the drill size needs to match the pin diameter so there is no movement at all from the template. This movement hasn't finished frying me yet, damaged thread in the plate crown wheel hole and two rubbed in cracked jewels, thats gonna be much more fun.
×
×
  • Create New...