Jump to content

How yemk install screws to call the phone it's not riding on the enabled

Khaledabdwatch
 Share

Recommended Posts

grsnovi Distinguished Member

grsnovi

Posted
Posted

You might consider using another translator - your headline makes no sense in the context of watchmaking.

You are showing a CITIZEN dial. I assume both front and back? If so, the back side has no location pins, so I'm assuming you locate the dial based on the day/date window?

I'm not familiar with how CITIZEN attaches their dials - other brands attach the dial by means of really small screws through the side of the movement however those screws typically press against a protruding dial stud (see 2 studs on rear of dial below).

rear of dial.jpg

Link to comment
Share on other sites
watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi as Gary pointed out both the dial feet are missing. There are several repair techniques available to restore the feet. There are stick on feet (avaiable from Cousins UK ) but with calendar complications you have to watch for the clearance. There are tools available to recess the dial to relocate the feet. The one below is a Cousins one but they are available from Ali Express far cheaper.  The other alternative is to re-solder new feet on,  like the attached which is my own that I built a while ago or the commercial alternative.

d58711_pic3_cmyk.jpg

DSCF3258.JPG.4fc73ff07a2632e67c70032771430121.jpg

Link to comment
Share on other sites
grsnovi Distinguished Member

grsnovi

Posted
Posted

Unless the watch has sentimental meaning to you - you might want to find a new dial.

There are several watches that appear to have a similar dial here however you would really need to know more about your watch, dial size and specific movement to ensure that any dial you get would align properly with the holes in the main plate.

Disclaimer - I have never purchased from India and have seen too many stories that suggest it isn't a great idea.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Bonefixer
      AS2063 - hand setting

      By Bonefixer · Posted

      The part was how it fell out of the movement - the train wheel bridge wasn’t screwed in.    I’ll probably dismantle the part, if I can, to work it out.    The train of wheels ran fine - it was only once the keyless works were installed I noticed the problem. 
    • mthomas828
      Balance staff sourcing?

      By mthomas828 · Posted

      Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Neverenoughwatches
      Epilame / Fixodrop

      By Neverenoughwatches · Posted

      Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
    • LittleWatchShop
      Movement holder made with 3D printer

      By LittleWatchShop · Posted

      Back home...printing now.  Will report results
×
×
  • Create New...