Jump to content

Modern Hermle clock--can I adjust the time backwards?


Recommended Posts

As a general rule, I do not adjust clocks counter-clockwise.  I realize this is overly cautious, but most of the time (e.g. Fall 1-hour adjustments) with pendulum clocks, I just stop it for an hour.  In this case, with an escapement, there is no easy way to stop it.

My question: Can I adjust the time by turning the time backwards?

If I were to remove the movement, it would be easy to figure out, but there is no other need to do so.  I just made one minor adjustment for the owner and fixed the bezel.

 

2022-06-24 12_57_46-20220624_124301.jpg ‎- Photos.png

Link to comment
Share on other sites

The simple answer is no. You should only turn the hands back if it is a time piece, any other wind up clock never, you can jam up the strike, chime or both and the clock will stop and you will most likely bend the minute hand or break the hand off.  

What you can do is put a little tissue paper and wedge it by the balance so it stops, or if the escape wheel is visible peg wood inside the escape wheel  to stop it. When it is the right time that the hands are showing just remove and it should start if not a little shake and all should be well. 

Link to comment
Share on other sites

39 minutes ago, oldhippy said:

The simple answer is no. You should only turn the hands back if it is a time piece, any other wind up clock never, you can jam up the strike, chime or both and the clock will stop and you will most likely bend the minute hand or break the hand off.  

What you can do is put a little tissue paper and wedge it by the balance so it stops, or if the escape wheel is visible peg wood inside the escape wheel  to stop it. When it is the right time that the hands are showing just remove and it should start if not a little shake and all should be well. 

That is my general rule.  However, some clocks are designed to allow this.  For example, the Seth Thomas ST124 (and variants) is designed to allow the hands to be turned backwards.  This Hermle...I don't know without removing the movement and checking it.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • My latest. Timex 2465. Replaced the crystal, caseback gasket and spring bars. All in less than $5US. Added a gray NATO strap I already had in stock.
    • I have some Gruen 510's in my donor pile if you need parts.
    • I've been intrigued by everyone's input here...so I decided to give this a shot. I bought the"typical" Pearl watch-machine basket and trays, for about $65. The trays are good,..the housing is a nightmare ! Thought it would take the mixer off my bench at anything above about 200rpm. The housing is cast of course,..and it's not "true" at all...so the harmonic vibration was insane. So,..I bit the bullet and bought the Elma housing and top. Not the baskets though, as the Pearl one's fit the Elma. Saved a bunch there. The basket and lid came to about $80 with shipping. The opening in the Elma top is 8mm, and the shaft that came with my stirrer is 6mm. I bought a piece of steel tube, 8mm O.D., and 6mm I.D. Cut off about an inch of the tube, and drove the rod into it. Gives a really snug fit.... Lightly champfered the leading edge of the 8mm section, then lightly tapped it into the top of the Elma lid. Spins like a dream now So... I have about $240 total into this including jars and steel mesh for the wave breakers   I'm pretty happy Best to you all   Randy
    • Still haven't gotten around to getting stems or screws, but I did make my first attempt at polishing a case. I just used a soft mop and rouge to reduce my odds of ruining them, and I think they came up pretty nice. Also gave the crystals a polish on the same wheel while I was at it. They were both very badly scratched up. The one on the left is fairly beat up, but it'll still make for a decent presentation.
    • You can try a rubber on that the sort for rubbing out a pencil.  
×
×
  • Create New...