Jump to content

Identifying lathe collet sizes.

Plato
 Share

Recommended Posts

Plato WRT Addict

Plato

Posted
Posted

Since I buy most of my tools second hand, especially those relating to lathes, I've ended up with quite a few unnumbered collets:

IMG_20220206_121530.thumb.jpg.4f3fc9c9064a988095ef60b65cb5853b.jpg

I only have pin gauges going up to 1mm in diameter and since they can't be measured with a caliper either I decided to use my lathe to measure them properly. I started with a 40mm brass rod and I'm gradually reducing it in diameter in 1mm increments until I identify each of the unnumbered collets; plus, I'm checking the condition of each of my numbered collets at the same time. Not sure if there's an easier way to do this but if nothing else it gives me a bit of practice time on the lathe 😀

IMG_20220206_121554.thumb.jpg.7cd09b3dbc59a023091b8637c519220d.jpg 

Link to comment
Share on other sites
Plato WRT Addict

Plato

Posted
  • Author
Posted
18 minutes ago, jdm said:

These are good https://shop.vogel-germany.de/test-equipment/jet-gauge-1-50-3-00-mm-16-blades.html

Also available 0.45 - 1.50mm. Apparently discontinued, that is the best price I could find.

Cheers, I was expecting them to be far more expensive, I'm just assuming watchmaking tool prices!

Any ideas how to permanently engrave the sizes on the collets? I've got a Dremel engraver but if there's a better tool/method...

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
1 hour ago, Plato said:

Any ideas how to permanently engrave the sizes on the collets? I've got a Dremel engraver but if there's a better tool/method...

Maybe photoetching? I've never tried myself, happy enough with a label printer and clear tape.

 

  • Thanks 1
Link to comment
Share on other sites
Plato WRT Addict

Plato

Posted
  • Author
Posted
18 minutes ago, nickelsilver said:

Keep in mind that the fact that a pin fits doesn't mean that's the size of the collet. They are usually sprung slightly open as made, and you can fit say a 2.1 pin in a 2.00mm collet- but it won't close correctly, run true or securely.

 

 

OK, maybe I'll just label them with permanent marker for now. I've been measuring them by making sure they go on freely and then hold with just pressure from gripping the end with my hand. So, my '25' could be actually a 24.

My method is flawed but I do have a general idea of the size, I'll just have to remember my numbering could be off when it comes to using them proper. Cheers.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • xdandeman
      Introduction: Bob Smith USN (ss) and dadd'y Elgin

      By xdandeman · Posted

      Nice file  Just got old pocket watch in and tools,  can I get it back together or should I give up.  we'll see  thanks for the info
    • Roll1ex
      Greetings from India.

      By Roll1ex · Posted

      @HectorLooi Yes, I would say that Mumbai has the highest liquidity in terms used watches. How was your experience with these used watches and what watch brands did you buy used? I have always found the vintage luxury watch segment in India a bit shady. Quite a few are genuine watches with genuine matching parts but just not from the same one.
    • Marc
      Seiko 6309a diver crown replacement

      By Marc · Posted

      Interesting interpretation of "traditional". I would say that Loctite is definitely the up-to-date and appropriate stuff to use, however, it is a relatively modern solution. Before the advent of such esoteric solutions I believe that the "traditional" thread locker of choice may well have been a sugar solution. Once applied the water would evaporate and the sugar would crystalise, locking the threads tight.
    • Marc
      Pocket watch winding stem sleeve

      By Marc · Posted

      @steve1811uk close but no cigar 🙂 I don't smoke anyway. I checked in my stock of parts and that's the closest I got to your dimensions. Good luck in your search. @RichardHarris123 I have an accumulation of all sorts of odds and ends that I acquired as a result of buying up the tail ends of old watchmakers estates. Usually after all of the great stuff has been stripped out, which means that the sweepings off of the workshop floor can be had for peanuts, but if you have the patience, can often be found to contain gold (both literally and figuratively 🙂 ). These came to me through on of those purchases. I doubt that I will personally be able to make use of even 10% of my accumulated stock, but having it, and knowing what I have, means that I can at least pass bits on to those who can use it whenever possible.
    • Curare
      Spell Check

      By Curare · Posted

      Hi and thank-you for your suggestions, as per Mark's instructions I checked my browser "Safari" and spell check and grammar was not ticked. So all sorted. Thanks CJ  
×
×
  • Create New...