Jump to content

Pocket watch crown wheel screws!

bosstaki

By bosstaki
in Watch Repairs Help & Advice

 Share

Recommended Posts

bosstaki WRT Addict

bosstaki

Posted
Posted

Hi guy’s! I’ve just opened up this pocket watch for inspection and the crown wheel screw launched its self out of the case & i can’t find it anywhere! Does anybody know what size the screw will be & if it’s going to be a left hand thread? 

7A48A0B7-D222-476C-8DD3-DFED94E81605.jpeg

Link to comment
Share on other sites
mikepilk Distinguished Member

mikepilk

Posted
Posted
On 10/9/2021 at 5:56 PM, bosstaki said:

 Does anybody know what size the screw will be & if it’s going to be a left hand thread? 

 

No, and yes, it will be left handed.

I start of searching with a torch, then move on to a powerful magnet. If that fails, clean the dust chamber/bag of the vacuum, and clean the whole area - floor, feet, desk, keyboard, everything, then empty on to some white paper.

By watch part standards, that's pretty big so should be findable. 

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • oldhippy
      Introduction: Bob Smith USN (ss) and dadd'y Elgin

      By oldhippy · Posted

      Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement. 
    • oldhippy
      First pendulum clock tinker

      By oldhippy · Posted

      Have you now repaired it? If so how is the time keeping.
    • dnhb
      First pendulum clock tinker

      By dnhb · Posted

      Yes: that's it exactly, right down to the break in the spring!!
    • HectorLooi
      Greetings from India.

      By HectorLooi · Posted

      I've bought brands like Citizen, Seiko, Titoni, Tissot, Roamer. Strange thing is many of them were using ST96 movements. I'm not sure if the ST96 is original to that model or whether it was a replacement movement.  All the watches with nice looking dials were obviously refurbished, after-market dials. And all of them had over-polished watchcases. Some of them had non-original hairsprings, rejewelled pallet forks, watch crystals that don't fit and glued in with a generous amount of glue. One of them was totally not working because the pallet jewel was loose to the point that it almost fell off. But the sellers were very nice. The seller of the non-working watch gave me a complete refund. Some of them gave partial refunds. I would say don't by luxury watches on the internet, regardless of the country the seller is from. Don't believe the "serviced by master watchmaker" statement. Have realistic expectations. ( Do expect the occasional complete junk.) Do expect to do a complete overhaul and major repairs. Otherwise, watches from Mumbai are great. For clocks.... I'm not so sure.
    • WpgRob
      Regulating an F6922 without a timegrapher

      By WpgRob · Posted

      In 2020,I picked up an Orient Mako II online. It ran at +15 seconds per day and after 3 years of resets more than weekly, it was time to crack the seal and take a shot at regulating it. Not having a timegrapher, I used a spreadsheet to track the time, referenced the Canadian NRC website, wore the watch between adjustments, and used the back end of some tweezers to lightly tap the regulator daily until it ran to within one second per day.   Two months later, it’s still running to within 1 second per day when measured over a week or longer, while daily variations are up to 9 seconds per day. For my purposes, its overall stability is surprisingly good. Is this method of adjustment “better” than adjusting to 5 positions using a timegrapher, since during the adjustment period the watch is already in the environment in which it’ll be used? Rob in Winnipeg 
×
×
  • Create New...