Jump to content

An Interesting Site From An Independent Watch Maker - V. Vyskocyl


Recommended Posts

Forgot to say, when you get to the site, look at the left-hand side index and click particularly on the "Theory" link - which leads into a set of good animations on escapements and other engineering aspects.

 

The English has been translated for him by a "bi-lingual" lady, so be aware of some complications in the explanations!

 

And here's the URL for his actual watch: http://www.vyskocil.de/4.0.html?&L=1

Edited by WillFly
  • Like 1
Link to comment
Share on other sites

Thank you so much for posting this. This goes back to the other thread on what we want from a watch for me. One mans vision with some out of the way thinking but packaged in a watch that is discreet. I wonder what the cost is? I would imagine looking at the case material and fit and finish its north of $20,000.

Link to comment
Share on other sites

That has just topped my "when I win the lottery" list.

 

From both the aesthetic and the mechanical design point of view it is about as close as it gets to my perfect watch for a modern piece. I love the open, un-crowded layout of the wheel train coupled with the huge barrel and balance wheel. And the fine regulator is beautifully executed. Fantastic.

It's interesting to compare the movement design with that of the Roger W Smith series 2 movement. Another hand made and beautifully executed design but very English in it's philosophy compared to this one.

 

It had better be a damned big lottery win 'cos there's one of those on the list too....

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Here are the pics of the bridge. Looks correct, but as soon as I screw on the rotor, the watch stops. Video here: https://1drv.ms/v/s!ArG5E62RGctxjokY5ws85BzuJLVakA   Pics.
    • One-dip or naphtha should be safe, but are you sure it isn't magnetized?  I would also check that.  Although, if that balance is from an Elgin 760 0r 761, I would think it would have a hairspring of non-magnetic alloy.
    • Hi, Is there a spell check function available when you are posting ? Regards CJ
    • Hi John I just did a Seiko Lord-Matic a front loader without a split stem, I used a crystal lift to remove it, although I had to have it that tight I though I was going to break the lift before the crystal would budge. So I decided that the press would be a better option as I think crystals with tension rings resist a lot of compressing. I used a crystal press to repalce it and the bezel with no issues, obviuosly a different watch to the Omega. I just took my time and kept inspecting the installation progress bit by bit Regards CJ
    • Hello All, I’m replacing the crystal in an Omega Dynamic, # 165.039, which houses a cal 552, installed through the front of the case. The replacement Sterncreuz crystal is, like the original, with tension ring. I removed the crystal using a compressed air technique to pop it out.  (I have a crystal lift, but I’m always fearful of marking the crystal edges and so avoid using it as much as possible). Now to the replacement -  any tips on putting the crystal back in?  Am I obliged to using my dreaded crystal lift to complete the task, or how about a crystal press?  I’ve put lots of crystals in using a press, but never with the movement in the watch. The thought of using one with a front-loader makes me very nervous, with the fully assembled watch sitting under the press. How would more experienced folks proceed here? Any advice, gratefully received… John Down Under…
×
×
  • Create New...