Jump to content

Recommended Posts

Posted

My Garrard Automatic has developed a loud click at almost every turn of the crown when hand winding. It appears to collect power ok though and also auto winds correctly and keeps working whilst wearing. I have taken the rotor off but have not been able to locate the source of the problem. Any assistance as to where I might start looking would be appreciated

P1010006.JPG

Posted

I'd be tempted to take the winder module off too, to see the click, rachet and winding wheel. You not only  have eliminate the parts you removed but might even see the fault starring at you, also wind through rachet wheel, that eliminates quite a bit for the least.

Its a process of elmination, next I guess is checking under dial.

Good luck

 

Posted

Does your watch have a caliber number? Then it almost looks like is a number under the balance rim that would be helpful if there's a number there? We might bill a find a tech sheet perhaps.

Then we can guess because we can't see the automatic mechanism so that probably has to come off. It may be that the reverser wheels have gotten sticky with time but that's just a wild guess. Also the other problem with automatic watches is often times they did not use jewels in critical locations and the holes where out to get oval. So basically this is exactly as mentioned above problem solving and you're going to have to take the automatic mechanism off. Then carefully look at all the wheels all of everything and you should build figured out hopefully

Posted

It's always amazing what you can find online if we take the movement number and the name they come up with the links below both of which suggests that the movement is based on  ETA 2783. From that we can a parts list.

https://antiques-atlas.com/antique/gents_unusual_1970s_silver_wrist_watch_garrard/as170a7214

https://www.birthyearwatches.com/product/1974-garrard-9k-gold-automatic/

496_ETA2750,1,2,6,4 ETA 2783.pdf

  • Like 1
Posted

Thanks JohnR725 for that connection... I must say the gold Garrard which is the same as mine seems rather expensive at £449. I sold 2 of mine last year at less than half that price. But I suppose that is why they stay on sale for month after month after month



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Thank you Mike for the hints! I did go to HS Walsh and buy few tools that will help me start 🙂 I also went to the Royal Observatory at Greenwich, I saw the collection and it is amazing!! Harrison H4 is indeed an amazing manufact, and the story behind it (about the prize from the government) is incredible. Again, thank you for your suggestions, you made my day!
    • Hello watch enthusiasts, I'm encountering a peculiar issue with my Seiko 4006 movement and could use some advice. Specifically, the alarm bolt yoke doesn't function properly when I tighten the screw on the calendar plate directly above it. This results in the alarm not functioning as it should. However, when I leave the screw loose, everything works perfectly and alarm bolt yoke is functional as should be. I've tried replacing the alarm bolt yoke, the alarm bolt yoke spring, and even the calendar plate itself, but unfortunately, none of these changes have made a difference. The only workaround I've found is to keep the screw on top of the alarm bolt yoke loose. Has anyone else experienced a similar issue or have any insights on what might be causing this? I'll also be sharing pictures to help illustrate the problem. Looking forward to your suggestions and advice! TT
    • Some news. After screws removal from donor movement, a family shot. From left to right: original (broken) screws new screws purchased from Cousins UK, as "Slava 2428 clamp screws", that didn't fit. They actually & definitively look too large screws removed from donor 2428 movement Here we go! First one is in position: Let's continue on the other side: Done! Next step will be putting back the hands. Another discovery for me! I keep going ...
    • OK, I have been there many times and know several solutions. As I believe, the pinion (the part with the leaves ) is on the other side of the arbor, yes? If so, then there is easy way to solve the problem. You can grind from one side as shown on the drawing with dremel tool. This will allow to push out the broken drill bit easy from inside. Then You will be able to insert new pivot and then You can solder it in place and in the same time to fill the ground portion with solder. Of course, I mean solder for PCBs, but not the led free one - use led containing solder, the led free solder which is offered in common hardware stores is for idiots.
×
×
  • Create New...