Jump to content

Mystery Heuer Chronograph...


Tudor

Recommended Posts

Hi Guys.

I want to build up this Heuer, but I know very little about it. I have the NOS dial, which I believe is for the 7734 (w/30-min counter), but I'm not certain. It's navy blue center with a lighter blue outer ring- a very sharp looking dial and I'd like to find the correct hands and case but I have no idea where to find that out. It is stored away, and I only have this lousy photo right now. I should have more photos and an OD measurement somewhere- I'll add that when and if I locate it. If I get my hands on the dial, I can indicate the feet positions, which should nail down the movement it should have.

So, I'm asking you all to take a look and see if you recognize the watch model and/or reference number, so I can build it up correctly.

Otherwise, I'll have to guess- using a basic round case and a Heuer crown. I think I have a red on white 7734 date wheel as well, but black on white is probably what was used. The red date with a set of red chronograph hands would look sharp on the blue and white. I think I can still get some neon orange Omega hands which would also look sporty on it.

Thanks!

001 (7).JPG

Link to comment
Share on other sites

I found this- which MIGHT be the case that was used, since most of the Heuers had the crown on the left and pushers on the right...

Heuer.jpg

 

And I found a Carrera with a right-hand crown and date... 

Edited by Tudor
Link to comment
Share on other sites

That’s great! Thank you!

Where did you find that? Are there more pictures or other info? That’s the first one I’ve EVER seen assembled!

 

8063972B-BE9D-401C-91C3-E98AEFFC0026.jpeg

Edited by Tudor
Added photo
Link to comment
Share on other sites

That's great, thank you!

I tried to find the base site from the full address and it wasn't coming up for me...

It's unfortunate that is a chromes brass case. I've found some similar ones in solid stainless that I may transplant into assuming the dial diameter is compatible. There is an eBay seller with new stainless cases that I guess he makes, or has made. They look decent and are reasonably priced.

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Hello, I am about 5 months into watchmaking and I love it!   The attention to precise detail is what really attracts me to it. (and the tools!) I am working on a 16 jewel 43mm pocket watch movement.   There are no markings besides a serial number (122248) .  The balance staff needs replacement. The roller side pivot broke off.  I successfully removed the hairspring using Bergeon 5430's.  I successfully removed the roller using Bergeon 2810.   Did i mention I love the tools?! I removed the staff from the balance wheel using a vintage K&D staff removal tool  with my Bergeon 15285 (that's the one that comes with a micrometer adjustment so it can be used as a jewel press as well as a traditional staking tool...it's sooooo cool...sorry..  can you tell i love the tools?) No more digressing..  I measured the damaged staff in all the relevant areas but I have to estimate on some because one of the pivots is missing. A = Full length  A= 4.80mm  (that's without the one pivot...if you assume that the missing pivot is the same length as the other pivot (I'm sure it's not)  then A = 5.12 mm...(can I assume 5.00mm here?) F=  Hair spring collet seat  F=  .89mm   (safe to assume .90 here? .. I am sure that my measurement's would at least contain  .01 mm error ?) G = balance wheel seat  G = 1.23 mm  (1.20mm?) H  =  roller staff  H =  .59mm  (.60 mm?) B  = bottom of the wheel to roller pivot   B  = 2.97mm  (3.00 mm?)     here I am estimating  again because this pivot is missing. So my friends, and I thank you profusely,  can you point me in the right direction as to how to proceed? Do i buy individual staffs?  or an assortment?   Since I don't know exactly the name of the manufacturer, will that be a fatal hindrance?   Tbh, I'm not even sure what country of origin this movement is. Thank you!    
    • Thats why i asked that question earlier, what happens if lubrication is placed directly on top of epilame ?  As opposed to walled within its non epilamed area . I'm not saying its right, i have no idea , just asking questions. 
    • thinking of where epilam should be removed did you know there was a patent that covers this? At least for the escapement I'm attaching it. GB1057607A-1 epilame.pdf
    • Back home...printing now.  Will report results
    • Oh well, if Master @nickelsilver says it's the way to go, then it is the way to go! I stand corrected! 🫡 Are there any other places where you're supposed to remove the epilame from the contact point of rubbing? I don't think so! Thanks for the effort @Neverenoughwatches, much appreciated! 🙂👍
×
×
  • Create New...