Jump to content

Oil filled watches


yankeedog

Recommended Posts

Hello all, 

Of late I have noticed that some folks have taken to filling their quartz  watches with oil. Either mineral  or silicone. In an effort  to increase their water resistance  by making them incompressible.I am also thinking I could not hurt to have the movement  immersed  in lubricant. Does  anyone  have any experience  doing this? Please  opine. 

Link to comment
Share on other sites

The real reason is to be able to see the watch underwater at angles without distortion. Silicone oil is the way to go as mineral can disintegrate plastic parts. Really unless youre a scuba diver its really not worth the effort as any future work will require extra work. Also once its filled theres no turning back without a complete restoration.

Sent from my SM-G950U using Tapatalk

  • Thanks 1
Link to comment
Share on other sites

did you notice if you go to YouTube where the video is the comments have been turned off? Always suspicious when I see a video or you cannot comment.

to get a better understanding I found a company that's doing it. Notice if you look at their link below the reference to mechanical watches can't be used because too much friction of trying to run in the fluid.  this is an interesting comment because quartz watches are even more susceptible to friction than mechanical watches. My suspicion is they designed a special quartz watch plus the reference to the lithium battery they probably have a super large battery to make up for all the energy loss of trying to drive the secondhand through a fluid. Also a note they don't actually say what the fluid is but I suspect that it's probably superlight fluid. So all the hobbyists filling their watches with mineral oil are going to get a very short running time.

 

https://www.sinn.de/en/HYDRO.htm

  • Thanks 1
Link to comment
Share on other sites

Thanks to all on your input.I suspect a higher  torque   movement  like maybe a ronda lithium  battery  one would be in order. What also intrigues  me is possible  increased  resistance  to vibration. I know that certain  instruments  used  in high  vibration  environments  were once oil filled.  I  ride a motorcycle  and have noticed that neither mechanical  nor  quartz  movements   can long tolerate  the vibration.  I was  wondering  if an oil filled  watch would have better  resistance  to this .opinions  please. 

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • What works for me (waiting for the villagers to assemble with torches and pitchforks) is to put a liberal (in watch terms) spot of 9010 on one of the pins of the pin pallet, this seems to improve amplitude and beat error.
    • Non-magnetic is a poor description of such a hairspring. A better description would be unmagnetisable hairspring. There are metals and alloys that are attracted to magnets, but don’t become magnetised themselves. A hairspring made out such a material will be attracted to magnetised tweezers, but will not become magnetised. These hairsprings can be disrupted by being in close proximity to a magnet, but the disruption will cease the moment the magnet is moved away. These are hairsprings that could conceivably be disrupted by a magnetised hairspring stud. Best Regards, Mark
    • More than enough. Here's mine at the height I work at. I think the working distance with the included 0.5x Barlow lens is about 9".   So yes, that halves the magnification. The full story is the objective lens goes from 0.7x to 4.5x. The eyepieces are 10x, giving you the advertised magnification of 7x-45x. However the working distance is unacceptably short, so it comes with an 0.5x Barlow lens, reducing the magnification range to 3.5x-22.5x, but giving you a good working distance. What I did was buy a pair of Extreme Widefield 20x Eyepieces for when I need more magnification. You keep your high working distance, but get your 45x magnification back, at the cost of some width of field.
    • Modern ones after blue steel, invar, elinvar and nivarox , the shiny one are not supposed to become magnetised. But i have had them jump to tweezers. And i dont really understand the comment that what can be magnetised is the stud carrier and rate regulator and they can attract the hairspring ? If the hairspring is non magnetic then how can it be attracted to something else thats become magnetise, its non magnetic , that doesn't really make sense to be ?
    • Does it say 17 jewels on the dial or on the movement ?
×
×
  • Create New...