Jump to content

Recommended Posts

Posted

Hello all, 

Of late I have noticed that some folks have taken to filling their quartz  watches with oil. Either mineral  or silicone. In an effort  to increase their water resistance  by making them incompressible.I am also thinking I could not hurt to have the movement  immersed  in lubricant. Does  anyone  have any experience  doing this? Please  opine. 

Posted

The real reason is to be able to see the watch underwater at angles without distortion. Silicone oil is the way to go as mineral can disintegrate plastic parts. Really unless youre a scuba diver its really not worth the effort as any future work will require extra work. Also once its filled theres no turning back without a complete restoration.

Sent from my SM-G950U using Tapatalk

  • Thanks 1
Posted

Compression isnt a factir unless your at great depths.....again....unless youre a deep dive scuba diver its not really worth it.

Sent from my SM-G950U using Tapatalk

  • Thanks 1
Posted

did you notice if you go to YouTube where the video is the comments have been turned off? Always suspicious when I see a video or you cannot comment.

to get a better understanding I found a company that's doing it. Notice if you look at their link below the reference to mechanical watches can't be used because too much friction of trying to run in the fluid.  this is an interesting comment because quartz watches are even more susceptible to friction than mechanical watches. My suspicion is they designed a special quartz watch plus the reference to the lithium battery they probably have a super large battery to make up for all the energy loss of trying to drive the secondhand through a fluid. Also a note they don't actually say what the fluid is but I suspect that it's probably superlight fluid. So all the hobbyists filling their watches with mineral oil are going to get a very short running time.

 

https://www.sinn.de/en/HYDRO.htm

  • Thanks 1
Posted

Thanks to all on your input.I suspect a higher  torque   movement  like maybe a ronda lithium  battery  one would be in order. What also intrigues  me is possible  increased  resistance  to vibration. I know that certain  instruments  used  in high  vibration  environments  were once oil filled.  I  ride a motorcycle  and have noticed that neither mechanical  nor  quartz  movements   can long tolerate  the vibration.  I was  wondering  if an oil filled  watch would have better  resistance  to this .opinions  please. 



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Sounds like you've either got a short somewhere or excess friction that's draining the battery. Are both insulators still under the battery.
    • I have only made screws down to M1 & 14BA & I had trouble getting the slot in the centre of the head so I made a jig to help me be more accurate when cutting the slot, here is my video.  
    • I would repeat what @nickelsilver says, and even more. I have at leas 10 old thread plates and I have never seen one that will cut like a normal die. I don't know if they are completely worn or have never been sharp enough, but I find them completely useless. And, for the new Indian ones, I have heard only bad things. For sure, if one tries to cut more thread on a winding stem, this hole of the plate is ruined. Further more, I have bad experience with all watch size thread dies that I could buy from the available machine  tool shops here. They could not cut normal thread even on brass rod. The size was significantly smaller and the pitch is like it should be for the claimed size... The thread shape was bad too. I will explain how I do threads. I use lathe that can cut threads and thus I can prepare perfect taps. I use milling attachment instead cutter in the tool post and so I can cut thread even on hardened rod. But I prefer to harden the rod after thread cutting and temper it only to light color change as to have the maximum hardness. Then I make a tap out of it by grinding. I prepare my dies for screw thread cutting with the taps I have prepared as described. In watchmaking, dies exist and are often used that are not cutting, but rather forming the thread. They are like nuts and don't have cutting holes and edges. This kind of dies I prepare and use. You will need soft steel plate , drill a hole in it, then cut thread, then make chamfer on one side, repeat the thread, harden. You can temper just a little or leave untempered, depending of the steel You use. Using such die is with soft steel rod (or completely annealed). Good oil is to be generously applied. The rod has to be with smaller diam than the thread size (about 0.8 - 0.9 x ), the diam is better determined by tries. The rod elongates by the thread forming too. When I have to make screws from harder material like SS, I just cut them on the lathe. You screw needs hardening and tempering to be finished as real screw.  
    • You could make a guide/jig. Cut a slot in a piece of metal approx the same thickness as the screw head, then drill a hole (screw head diameter) in that slot.
    • Tried a SR920W and its completely dead after 3 weeks 🤷‍♂️ 
×
×
  • Create New...