Jump to content

Myota FS60


Recommended Posts

Hi

I usually tinker with mechanical watches but a friend has given me his Citizen Edifice (Myota FS60 movement with AG1 cell) to look at for him. The battery when replaced will only last 2 weeks or so. Any suggestions on what it could be or am I better just putting in a new movement?

Link to comment
Share on other sites

19 minutes ago, watchweasol said:

Hi I would not reccomend AG cells  some are ok but not all

Be aware, AG is not a brand just an old  denomination standard for Alkaline (1.5V) button batteries, as such these are never apt for watches (except some large Chinese quartz modules). For a quartz watch one should use SR (Silver Oxide) batteries with a 1.55V and longer lasting.

Since AG sizes are the same as some watch batteries, and they cost marginally less, sometime these are incorrectly fitted "in lieu". 

Below a shameless copy from the internet of AG sizes:

AG SERIES AND CORRESPONDING MODEL NUMBERS FOR EACH AG#

AG0 Button Batteries: 379, LR521, LR63, 618, GP379

AG1 Button Batteries: 364, LR621, LR60, D364, LR620, 280-34

AG2 Button Batteries: 396, 397, LR59, LR726, 612, 196, D396, D397

AG3 Button Batteries: 384, 392, 192, LR41, LR736, L736, GP192, V36A

AG4 Button Batteries: 376, 377, G4A, LR66, L626, LR626, GP77

AG5 Button Batteries: 393, 309, 193, LR754, LR48, D309, D393

AG6 Button Batteries: 370, 371, LR69, LR920, LR921, D370, D371

AG7 Button Batteries: 395, 399, LR926, LR927, LR57, D395, D399

AG8 Button Batteries: 381, 391, L1120, LR1120, L1121, LR1121, LR55, D381, D391

AG9 Button Batteries: 394, LR45, LR936, D394, GP394

AG10 Button Batteries: 389, 390, 189, L1130, LR1130, L1131, LR1131, LR54, D389, D390

AG11 Button Batteries: 361, 362, LR721, LR58, D361, D362

AG12 Button Batteries: 301, 386, L1142, LR1142, LR43, D301, D386

AG13 Button Batteries: 357, LR44, L1154, A76, PX76A, 303, D303, D357

  • Thanks 1
Link to comment
Share on other sites

20 hours ago, jdm said:

Be aware, AG is not a brand just an old  denomination standard for Alkaline (1.5V) button batteries, as such these are never apt for watches (except some large Chinese quartz modules). For a quartz watch one should use SR (Silver Oxide) batteries with a 1.55V and longer lasting.

Since AG sizes are the same as some watch batteries, and they cost marginally less, sometime these are incorrectly fitted "in lieu". 

Below a shameless copy from the internet of AG sizes:

AG SERIES AND CORRESPONDING MODEL NUMBERS FOR EACH AG#

AG0 Button Batteries: 379, LR521, LR63, 618, GP379

AG1 Button Batteries: 364, LR621, LR60, D364, LR620, 280-34

AG2 Button Batteries: 396, 397, LR59, LR726, 612, 196, D396, D397

AG3 Button Batteries: 384, 392, 192, LR41, LR736, L736, GP192, V36A

AG4 Button Batteries: 376, 377, G4A, LR66, L626, LR626, GP77

AG5 Button Batteries: 393, 309, 193, LR754, LR48, D309, D393

AG6 Button Batteries: 370, 371, LR69, LR920, LR921, D370, D371

AG7 Button Batteries: 395, 399, LR926, LR927, LR57, D395, D399

AG8 Button Batteries: 381, 391, L1120, LR1120, L1121, LR1121, LR55, D381, D391

AG9 Button Batteries: 394, LR45, LR936, D394, GP394

AG10 Button Batteries: 389, 390, 189, L1130, LR1130, L1131, LR1131, LR54, D389, D390

AG11 Button Batteries: 361, 362, LR721, LR58, D361, D362

AG12 Button Batteries: 301, 386, L1142, LR1142, LR43, D301, D386

AG13 Button Batteries: 357, LR44, L1154, A76, PX76A, 303, D303, D357

This was very useful as I do not normally look at quartz watches, and my knowledge here is poor  thankyou very much 

Link to comment
Share on other sites

20 hours ago, watchweasol said:

Hi I would not reccomend AG cells  some are ok but not all, first check the cell with a meter, If the voltage is below 1.3 / 1.4 it is us. I personally always fit Renata batteries but get them from a trusted source ie  Cousins.uk  as there are even fake batteries on the market

8299_Miyota FSXX Series Parts List.pdf 236.35 kB · 1 download

Great thank you very much

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Bringing this old thread back to life, as I have similar problem. I did follow this advice, but while inserting a male stem (crown side) and just pushed it to the female part, and the fork (female side) of the stem has broken. What is the right way? Push the stem part so it widens the gap and fits in? Why it was then receiving side got broken? Old metal? It is a vintage watch from late 60s.    or the outer part should be inserted somehow from the side (slipping to the gap), but I don’t have space there for this manipulation. The watch is Orient Fineness monocoque case.   thank you!  
    • Thats insane Nev that you cut those tiny pinion teeth with a cutter you designed and made. 
    • I certainly do Razz. Ive just started work on this AS554, interestingly enough it had a paper dial made from a postcard , look at the brand name on the dial, very curious. 
    • [SBGA405] Grand Seiko “Godzilla” Spring DriveI always enjoy coming back at the end of the week to my first Spring Drive watch which is a combined automatic mechanical watch and a high quality quartz — a Spring Drive.Impressive accuracy (10 seconds per month) and wears remarkably comfortable at 44.5 mm in diameter and 95 gm.Love the power reserve indicator, and the colour of the dial amd the watch band.One of my “perfect” watches!!😍
    • Yep, so we got a 10 1/2  ligne movement, thats the starting point now these bad boys books should hopefully get us across the finishing line . Next we need a good clear picture of that rocking bar, the setting lever and the setting lever spring. I've already got an idea what it might be.  
×
×
  • Create New...