Jump to content

Elgin Direct Reading Jump Hour - Disc Removal Tool

Wdc

By Wdc
in Tools & Equipment

 Share

Recommended Posts

Wdc Watch Enthusiast

Wdc

Posted
Posted

Elgin Direct Reading Jump Hour - Minute Disc Removal Tool

Does anyone have any information that would help me identify and source one of these tools, i.e. Elgin's description, part number, etc..

I've spent hours chasing leads with one description or the other, to no avail. Possibly if I had a more descriptive identification, it would help in my search. Most searches lead back to the Crazywatches article which has some good photos of the tool but lacks description or part number identifying the tool.

Any help identifying it and/or sourcing one would be appreciated. Possibly a photograph of the markings on the tool.

Thanks in advance,
Will

Footnote: Photographs from the above crazywatches article - "a special set of tweezers was designed for quick and safe removal of disc”.

 

TOOL-elginjumphourtool2.jpg

TOOL-elginjumphourtool1.jpg

TOOL-elginjumphourtool4.jpg

Link to comment
Share on other sites
Wdc Watch Enthusiast

Wdc

Posted
  • Author
Posted

No you must press down on the pin (minute) in the center of the hub otherwise the entire caboodle comes off and everything has to be reset.  The tool allows you to pick up on the minute wheel while holding down the canon pinion.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      I did that also for a few movements - well, mainly in/around the train jewels. I made big efforts to epilame the mainplate WITHOUT getting Epilame into the Pallet fork jewels (where it's not supposed to be, right?). I made litte barriers with Rodico around that jewel and used drops from a syringe to apply on the rest.  However, I've now stopped doing this. For three reasons: 1. It's a hassle and consumes more of this liquid gold. 2. I didn't see the need when using HP1000/HP1300 lubricants and grease for most part. The two places where I'd use 9010 (i.e. escape wheel and balance) receive Epilame in specific places... or the cap-jewel-setting of the balance suspends the oil sufficiently be capillary action (see my "conflict" about using Epilame on the balance jewels).  3. Lastly, and here I really wonder about yours and others' experiences: I felt that applying Epliame to the train jewels left them looking hazy (borderline dirty) compared to the (painstakingly achieved) sparkly clean results of my cleaning process. I just can't help but think that the Epilame residuals would mix with the oil and cause more friction/wear. I don't know.    simple: it'll stay there. It won't move any further. That's exactly what is happening if you epilame a cap stone. You end up placing the 9010 right on top of the epilame and the oil will sit nicely on that spot.
    • Neverenoughwatches
      Coil for old Seiko Credor -- 4002920

      By Neverenoughwatches · Posted

      There are some parts on Ebay for the seiko 6020A, it may just be a waiting game for someone to strip one down, NOS will be more scarce . K would strip your movement down to the module then start looking at other seiko movement to see if that coil is used, then seek out a seiko part dealer. Also Retrowatches youtube owner Mike may give you some advice try him on his site . He also hangs around amateur watchmaking groups.
    • Waggy
      Setting lever spring

      By Waggy · Posted

      I would agree, in order to work harden something you need to exceed it's yield strength when it moves from the elastic zone to the plastic zone and you get permanent deformation and work hardening which is fairly close to its failure point, relatively speaking and dependent on the material/alloy of course. In theory you can load something constantly within its elastic range and not suffer work hardening issues.
    • Waggy
      Coil for old Seiko Credor -- 4002920

      By Waggy · Posted

      Probably easier to get a complete new movement - but CousinsUK list it as discontinued. Maybe someone on here knows a substitute movement ?
    • Kkramme
      Coil for old Seiko Credor -- 4002920

      By Kkramme · Posted

      Any other thoughts on how I can get a replacement coil? Any “hidden” or unknown physical shops (in Australia or elsewhere) that might have them in stock (but not always online)?
×
×
  • Create New...