Jump to content

Mounting Bridge on Cement Chuck And Achieving Center


SparkyLB

Recommended Posts

I have an older scrap movement with a train bridge of the long slender variety.  It has two screws, one on each end, and contains only the jewels for the center wheel and the 3rd wheel.  Both jewels are rubbed in.  This is one of the first movements I bought, and did not have the ability to successfully free the jewel by the correct method.  Instead, I reamed out the hole using a .229mm reamer from my Seitz jeweling tool, and confirmed the remaining hole is parallel, sharp, and very clean.   

I purchased from Otto Frei a 2.30 mm OD jewel with the proper size jewel hole.  (The third wheel pivot measures .16mm, and the jewel I ordered has a hole of .17mm.)  I have recorded the depth of the original, badly cracked jewel before removing it.  Installing a new friction-fit jewel at the right depth should not be an issue.  

In retrospect, I would think I should have mounted the bridge on a cement chuck and using a lathe, and an appropriate tool; coax the rubbed-in metal open, allowing the rubbed in jewel to fall free.  My question stems from my inability to accomplish this. 

How does one mount an irregularly-shaped item (like this long curved bridge) on a cement chuck in order that the jewel hole is perfectly centered, and there is no wobble when the lathe spins?  I would be using shellac as an adhesive.    

I've searched about a bit, but as a novice, I probably don't yet know the correct questions to ask to get help from sources like google or youtube. 

My only option was to provide a long-winded explanation of my issue.  Any replies would help me greatly moving forward. 

 

 

 

Link to comment
Share on other sites

Thank you, nickelsilver.  You're always very helpful.  I'm guessing by faceplate you mean one of these?

faceplate.png.d4323bf0cf6aadb9240047b12271dcbb.png

If I only have a cement chuck, such as this:

1558227257_cementchuck.png.a66c8a26b52e614e5c9c1d1629f4fd55.png

can I still accomplish what you speak of?

I understand one can tap work into place on a faceplate.  A cement chuck would have to have the work affixed and in place in a very short window of time, i.e. before the shellac hardens.  Is this possible? 

Could one maybe mount a centering stake to the tailstock and while the shellac is hot, position the work onto the cement chuck mounted in the headstock with the jewel hole centered?  I appreciate everyone's patience.  I've taken Mark's 3 courses, and have probably spent days on YouTube, but I've never seen this scenario addressed. 

 

Link to comment
Share on other sites

Hi  The method mentioned by Nicklesilver is the preferred method but lacking the face plate the method you propose using the lathe and centering whilst the shellac is still soft is also possible. Both methods are explained in De Carles book "practical watch repairing" 

  • Like 1
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Welcome to the forum, enjoy. I have a varimatic that went  out of sequence because it’s hydronic oil ran very low. Must admit it’s still in my garage just know time to fix it. Purchased a cheap Indian Junta/ sonic Pearl as a stop gap a few years ago and it still performs perfectly so no incentive to fix the Varimatic. 
    • The plate is OK, thanks. It seems the answer to my question is that this is a 'hack' & for me another reminder that in general, one won't be the first person to be tinkering with an old timepiece!. As you day, I've been fortunate to have gotten some good advice and, just as important, encouragement. I've been lucky then not to have the balance spring break as a result of my novice 'ministrations' - but I did remember to 'stroke' rather than bend per se. The clock is of sentimental value to the owner so I'm relieved to have now got it running to time with the support & encourage of forum members like yourself.
    • Recently purchased a L&R Varimatic knowing that the piston does not fully rise in the cylinder. The likely cause is air in the system. The manual calls for using a bleeder cup, which is as rare as hen's teeth.Does anyone have any experience with this issue and if so, how did they resolve it?
    • Thanks ww, its maybe not as much of a bodge trick that i thought it was. 
    • Thank you for your introduction and welcome to this friendly forum. We all look forward to your contributions and continued involvement.  It would be nice if you told us a little about yourself.
×
×
  • Create New...