Jump to content

For Those Who Work On Kinetics


Recommended Posts

Only have a closeup of mine.

20141103_14111301.jpg

The watch sits upright. You can use foam to wedge it so it stays put smack in the centre of each ring.

Took 4 days to fully charge mine.

Edit.

Its the base from this set.

279751_IMAGEO-Candle-Light_xxl.jpg

Edited by ro63rto
  • Like 1
Link to comment
Share on other sites

Thank you ro63rto! I'll check those out on ebay, I believe it is what I was looking for!

Cheers,

Bob

One thing to point out though.

I have not opened it up to bypass the timer feature so every few hours i have to press the reset (red led) to resume charging. One day I'll get round to it.

Link to comment
Share on other sites

  • 2 weeks later...

I've only had one kinetic watch (a Seiko Arctura chrono), and had no trouble in keeping it running when it was off the wrist. When it did run down, it took a few hours to get it back to an even tick - rather than the 2-second jump that the second hand makes when it's underpowered - but apart from that it ran more or less continuously on a day's worth of normal wrist time..

 

It always seemed odd to me to save battery costs by buying a kinetic - and then use an electrically powered winder to keep it going! In the end I sold it as the chrono function was faulty, and got a solar powered Seiko instead. I much prefer solar power.

  • Like 1
Link to comment
Share on other sites

Are those obsolete now, or do they still make them?

I got mine from A.G.Thomas some time ago, but their website is such a mish mash, it would probably pay to phone them.

 

I don't think Seiko have ever officially sold them, I just think that occasionally the suppliers acquired them.

Link to comment
Share on other sites

I have seen them in esslinger and ofrei, maybe even in borel but the price....the quote in my first post is from esslinger! Too rich for me and I don't even have one kinetic yet....although some will be refurbished soon. :)

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • This is a flying cutter, usual one. The cutter itself is shown in the pictures in the first message, it is made of broken tungsten carbide drill bit. I asure that all the angles of the cutter are as they should be. I have video - little older one - that I made when onse making the same kind of winding pinion for a Poljot 2200, which is even smaller than this one. It is not easy to see in the video, but the tool rest moves about 1mm towards the object in Y direction and then returns back untill cutter is rotating. Then the spindle is rotated one tooth ahead and everything repeated untill all teeth are cut.
    • After a bit further research could it possibly be an AS 970?
    • Latest project was a non-running ebay purchase with an FHF70 movement. I stripped and cleaned it, reassembled it, and got it running. So far so good, nothing damaged AFAIK.  I was oiling the top jewel on the balance (the one in the cock) which was a slightly unusual shock setting. I removed the spring (3 leaves) which was part of a chaton holding the cap jewel. This left the hole jewel behind which I retrieved with rodico and then lost it. I was taking it off the rodico, very gently as I thought, with tweezers, and then it just disappeared.  Fast forward a week, I got a donor movement, non-running, with the plan to just take the shock jewel that I’d lost. It was the same movement but had standard incabloc settings, and was steel rather than copper/brass.  I changed the cock and balance complete and it ran, not very well. I switched the lower jewel setting, cleaned and oiled both jewels and the replacement balance. Without the pallet fork the balance swings very nicely with a puff of air. With the fork in place, balance out, it flicks side to side nicely with power in the mainspring.  Put them together and it doesn’t run. The impulse jewel sits in the fork and it stops.      Any suggestions how I proceed? In case you didn’t follow that I have 2 FHF70 movements, nothing broken as far as I can tell, but mixing up the balance wheels and jewel settings results in a non runner. 
    • Oh and this almost perfect third wheel pivot and slightly set mainspring  Ah ok yes i see what you mean, good idea. I'll try that if i fluff this one up. The image isn't great quality but i like the idea though.
    • Why cut the paper, cut a square around the image and grind to it. 
×
×
  • Create New...