Jump to content

6497 Second Wheel Pinion Removal

mcoulton

By mcoulton
in Watch Repairs Help & Advice

 Share

Recommended Posts

mcoulton Watch Enthusiast

mcoulton

Posted
Posted

Hello

On my  ETA 6497 clone the second wheel has a pinion that prevents it from passing through the jewel and removing the wheel from the movement. I've read elsewhere that a pair of nail clippers can be used to cut the stem! Is this the preferred method or are there other suggestions? Also if I remove / cut / shorten the 2nd wheel stem, where does the second hand go or can any second hand be installed into the modified second wheel?

Thanks in advance for any help that can be given.

PS. This is the first movement I've ever taken apart and put back together. It may also be the first movement I destroy; only time will tell! All in all it's been a good experience and I've managed to re-capture all flying objects except for the click spring screw!

Link to comment
Share on other sites
jaycey WRT Addict

jaycey

Posted
Posted

There should be nothing to prevent removal of that wheel.

A photo of the pinion (not stem!) would give us some idea of what is preventing removal. Do not cut it!

 

The 6497 is a great starting movement to work on, good luck.

Link to comment
Share on other sites
mcoulton Watch Enthusiast

mcoulton

Posted
  • Author
Posted

Hello

I looked at this again and was easily able to pull the pinion off the second wheel. I believe it was a "spacer" to allow for the second hand (that came with the movement) to be installed. When it comes time to add a replacement second hand I'll need one that has a hole of about .25mm (according to my digital caliper). I can't use the spacer as it was pinched while being removed. The second wheel pinion doesn't have a hole in it to install a pin type second hand. I hope I'm explaining myself well enough. Does what I've written make sense? 

Thanks in advance for any help. 

Michael

Link to comment
Share on other sites
mcoulton Watch Enthusiast

mcoulton

Posted
  • Author
Posted

Hello 

I forgot to add the specification sheet for the ETA 6497-2 doesn't give a pinion measurement for the second wheel. The only measurement I'm able to get is the one via my caliper and I don't know how accurate this would be as I haven't tried to source any hands and try them out. Don't know that I will buy any hands as this is a practice movement. 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
On 4/17/2019 at 5:38 AM, mcoulton said:

On my  ETA 6497 clone the second wheel has a pinion that prevents it from passing through the jewel and removing the wheel from the movement. I've read elsewhere that a pair of nail clippers can be used to cut the stem!

I think what was meant was to use a nail clipper to pull. There are, of course, specific tools for that.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • AlanB
      Gilding after silver soldering

      By AlanB · Posted

      When faced with say a pocket watch bridge which is cracked, silver soldering to repair is often the only option (hopefully someone wasn't there before hand with soft solder). I can generally do this succesfully and tidily with a small torch and miniscule pieces of silver solder, but on parts which were mercury amalgam gilded the heat can have have a deleterious effect on the finish.   I keep wondering if there's a good way to refinish these - and despite having the needful items would rather avoid using the mercury process.   In the past for electronic work I've gold plated PCBs but this involved gold potassium cyanide solution, which also doesn't realy belong at home. I've read that there are now safer alternatives but couldn't find more detail (and importantly how similar are the results to amalgam gilding, since I wouldn't want to refinish the whole watch). Pointers would be very welcome (and yes, I know solutions containing gold won't be cheap!) Alan
    • Neverenoughwatches
      Can anyone identify what this is? Part Two

      By Neverenoughwatches · Posted

      The first one is an Unruh max stake for pushing out staffs
    • JonC
      Can anyone identify what this is? Part Two

      By JonC · Posted

      Ok so with the great answers for my previous question may I ask what these two attachments are used for. The one with the red knob is I assume used for hand setting the seconds hand? Jon      
    • Zedster
      Roamer Searock Crystal problem

      By Zedster · Posted

      According to Cousins site I need to look at document G22 as I think I need an ATGB at 304 but I cant find this size in G22 doc. The last thing I want to do is order the wrong one😳  Unless I cant see the wood for the trees 😆 I could be looking at the wrong style, I assume its classed as Round plastic Armed  https://www.cousinsuk.com/product/wide-ring-gold-atgb
    • JonC
      Dial feet removal

      By JonC · Posted

      When building a new Watch I have tended to use a file to remove the remnants of dial feet that are not needed as many dials come with four feet to accomodate different movements, but this can be a bit messy so now I use this with a great deal more precision as you can use an appropriate bit for the job and keep it very localised.      
×
×
  • Create New...