Jump to content

Home-Made balance tack

Tudor

By Tudor
in Tools & Equipment

 Share

Recommended Posts

Tudor Distinguished Member

Tudor

Posted
Posted

Hey guys.

 

Been occupied by other things lathely, namely getting an old lathe up and running here at work...

It's quite beat and abused but Its a high quality Hardinge lathe. I rebuilt the compound (which clips onto the dovetail way as it's a lower-end second-operation lathe) so it has limited travel. The angle scale (which is under the top of the compound and visible through a magnifying glass built in) was completely covered in rust and grease. Now it's visible... It came in handy to set ~2 degrees of taper for my tack! I also took the excessive lash out of the compound ways so they are nice and tight now. This is a sweet lathe with a 3-jaw chuck as well as an assortment of 5C collets. I learned from a master tool and die maker on the high end version of this- the tool room lathe, with a proper apron able to cut inch and metric threads. This is it's lesser cousin.

A brass rod was tapered as thin as I could and then finished with sand paper as it was deflecting from the tool of course and not cutting as it got thin... I pressed it into a 1" slug of aluminum. A bit of tubing to keep it safe and a recycled container and we are done!

Anyway, here's the tack:

tack 001.JPG

tack 002.JPG

tack 003.JPG

  • Like 2
Link to comment
Share on other sites
  • 2 years later...
Tudor Distinguished Member

Tudor

Posted
  • Author
Posted

Thanks. 
 

I think the tack is easier. Just grab the assembly with your tweezers and set it in place. It seems to just fall into alignment with the fork. That was the whole reason for opening this- I dropped it and it stopped, so I figured the balance wheel or pallet fork jumped. Pallet fork was fine, and once I set this in and lined it up, it started running before the screw was in. 
 

This kept excellent time before it hit the floor and still does now, so no adverse effect to hanging it. 
 

It was only hanging a few minutes. Just long enough to check the escapement function. 

Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted
1 hour ago, Tudor said:

I dropped it and it stopped, so I figured the balance wheel or pallet fork jumped. Pallet fork was fine, and once I set this in and lined it up, it started running before the screw was in. 

Overbanking can be diagnosed and fixed without removing the balance. Rotate gently the balance with a brass tweezer or wood, it will move one direction but having a firm stop in the other. Loosen the cock screw, lift a the balance rim a bit and rotate in the direction where it couldn't go. It will start running, tighten back, check on the timegrapher and if no more trouble job is done.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • AlanB
      Gilding after silver soldering

      By AlanB · Posted

      When faced with say a pocket watch bridge which is cracked, silver soldering to repair is often the only option (hopefully someone wasn't there before hand with soft solder). I can generally do this succesfully and tidily with a small torch and miniscule pieces of silver solder, but on parts which were mercury amalgam gilded the heat can have have a deleterious effect on the finish.   I keep wondering if there's a good way to refinish these - and despite having the needful items would rather avoid using the mercury process.   In the past for electronic work I've gold plated PCBs but this involved gold potassium cyanide solution, which also doesn't realy belong at home. I've read that there are now safer alternatives but couldn't find more detail (and importantly how similar are the results to amalgam gilding, since I wouldn't want to refinish the whole watch). Pointers would be very welcome (and yes, I know solutions containing gold won't be cheap!) Alan
    • Neverenoughwatches
      Can anyone identify what this is? Part Two

      By Neverenoughwatches · Posted

      The first one is an Unruh max stake for pushing out staffs
    • JonC
      Can anyone identify what this is? Part Two

      By JonC · Posted

      Ok so with the great answers for my previous question may I ask what these two attachments are used for. The one with the red knob is I assume used for hand setting the seconds hand? Jon      
    • Zedster
      Roamer Searock Crystal problem

      By Zedster · Posted

      According to Cousins site I need to look at document G22 as I think I need an ATGB at 304 but I cant find this size in G22 doc. The last thing I want to do is order the wrong one😳  Unless I cant see the wood for the trees 😆 I could be looking at the wrong style, I assume its classed as Round plastic Armed  https://www.cousinsuk.com/product/wide-ring-gold-atgb
    • JonC
      Dial feet removal

      By JonC · Posted

      When building a new Watch I have tended to use a file to remove the remnants of dial feet that are not needed as many dials come with four feet to accomodate different movements, but this can be a bit messy so now I use this with a great deal more precision as you can use an appropriate bit for the job and keep it very localised.      
×
×
  • Create New...