Jump to content

Help With A Loose Vintage Minute Hand.

chrisbuxton27
 Share

Recommended Posts

clockboy Distinguished Member

clockboy

Posted
Posted

A controlled nip is required. For this reason I put them in a lathe collet and GENTLY tighten. It is really,really easy to go to far. You can use a broach but I recommend you put the broach in a vice so you have total control. 

Link to comment
Share on other sites
chrisbuxton27 Watch Enthusiast

chrisbuxton27

Posted
  • Author
Posted

Clockboy the type of minute hand I mean has no stem just a flat hand with a hole to push onto the minute wheel. So there is nothing to place in the lathe collet. I'm thinking a stake of some shape to to close the gap slightly but not sure which would do it. Maybe a stake used for setting jewel stones would do it but that's something I've not tried either.

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted

Ok sorry did not read the post correctly. However I recommend to get hold of the Cousins catalogue and browse it.

There are lots of hands available , different styles etc.  You will need to know length,width hole size etc. Too small is Ok because you can broach the hole out to fit but to big I really don,t know a way around it. Using a staking set punch might be to much for a delicate hand. The cleaver boys (not me) would make another arbour with a fatter shaft or thin the minute arbour and put a sleeve on. But you need a watchmakers lathe and lots of skill which I do not possess.

Link to comment
Share on other sites
Charlie WRT Addict

Charlie

Posted
Posted

On a proper staking set you will find several hole reducing punches. The five blued punches with round polished ends are the ones I use to re-size hands. Smaller seconds hands as found on sub-seconds dials with tiny tubes I do with my set of pin vises. There are also other ways to accomplish this task, but I find these punches work well for me. I will post a photo shortly.

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      Yes, I was referring to the (jewelled) gear train with HP (most of the time, I use 1300, but when Rolex says 1000, I'll use 1000).
    • JohnR725
      Without Our Forum

      By JohnR725 · Posted

      did I miss the update of the message of something changing?      
    • JohnR725
      Epilame / Fixodrop

      By JohnR725 · Posted

      I suppose it would depend upon what your lubricating with those? for instance what does the manufacturer say about those lubricants? I have a PDF from the manufacture and a rather peculiar statement found on the bottom of the chart. my suspicion is the reason the recommending would be without epilam the HP oils like the spread except when they're in Ruby jewel's with steel pivots. tableEN lubrication 2020.pdf
    • oldhippy
      Is this a 'hack' ?

      By oldhippy · Posted

      These types of hairsprings become weak with age and very fragile. Which I expect it is that giving you trouble, and that wheel is not the correct one, if it were not bent I don't think the movement would run as the teeth are not the correct height. The problem you have is price which depends on you. It can be repaired but is it worth it to you, because there is little value in the clock. A wheel can be made and hairspring replaced. Or hang on to it and keep looking on ebay which is your best bet for replacement parts or even a complete movement but it will be like finding a needle in a haystack. 
    • Knebo
      Epilame / Fixodrop

      By Knebo · Posted

      I did that also for a few movements - well, mainly in/around the train jewels. I made big efforts to epilame the mainplate WITHOUT getting Epilame into the Pallet fork jewels (where it's not supposed to be, right?). I made litte barriers with Rodico around that jewel and used drops from a syringe to apply on the rest.  However, I've now stopped doing this. For three reasons: 1. It's a hassle and consumes more of this liquid gold. 2. I didn't see the need when using HP1000/HP1300 lubricants and grease for most part. The two places where I'd use 9010 (i.e. escape wheel and balance) receive Epilame in specific places... or the cap-jewel-setting of the balance suspends the oil sufficiently be capillary action (see my "conflict" about using Epilame on the balance jewels).  3. Lastly, and here I really wonder about yours and others' experiences: I felt that applying Epliame to the train jewels left them looking hazy (borderline dirty) compared to the (painstakingly achieved) sparkly clean results of my cleaning process. I just can't help but think that the Epilame residuals would mix with the oil and cause more friction/wear. I don't know.    simple: it'll stay there. It won't move any further. That's exactly what is happening if you epilame a cap stone. You end up placing the 9010 right on top of the epilame and the oil will sit nicely on that spot.
×
×
  • Create New...