Jump to content

Skagen Hagen SKW 6217 BATTERY CHANGE

beearchie

By beearchie
in Watch Repairs Help & Advice

 Share

Recommended Posts

beearchie Member

beearchie

Posted
Posted

I own a Skagen Hagen SKW6217 watch.
The battery just died in it.
I can't seem to figure out how to replace it. Read online about it's top load design and unit body form.
All I see is a screw at the back of the watch.
All the jewellers I have taken it to are unable to replace the battery cos they can't seem to open it. Is there anyone who can help guide me on how to open it?

IMG_20180101_233047978.jpg

  • Like 1
jdm Distinguished Member

jdm

Posted
Posted
Just now, beearchie said:

I have to take out that screw at the back first, right?

Will try this tomorrow and give you feedback on this.

Under the screw should be the stem release point.

  • Like 1
Ishima Super WRT Addict

Ishima

Posted
Posted

Some models of Skagen are sneaky, i did a little bit of googling for this model but could not find it. I was considering that it might even be solar powered, i've come across two skagens that were solar powered but did not state anywhere on the outside of the watch that it was, and they both had that line on the back with the model name in the lower right hand of the line. 

Honestly if you can't find a watch specialist who's competent to do this I strongly suggest returning to manufacturer. 
http://www.skagen.com/us/en/service-information.html

However, I will say that it is very likely that the crosshead screw on the back comes off to expose 'the setting lever' which can be pressed to release the winder and from there once you have the front off it should be possible to drop it out. 

  • Like 1
Ishima Super WRT Addict

Ishima

Posted
Posted

oh, i just found it actually, okay looks to be regular quartz, not solar. and the front should be removable by prying off, it's also a little less expensive than i assumed so I could understand some reluctance in going through a Skagen workshop, however, I will re emphasize this could go horribly wrong for you without the right experience and tools. 

  • Like 1
beearchie Member

beearchie

Posted
  • Author
Posted
6 minutes ago, jdm said:

Under the screw should be the stem release point.

I have seen something like that when I took the screw out. How do I work that to pop out the crown?

jdm Distinguished Member

jdm

Posted
Posted

 

6 minutes ago, Ishima said:

oh, i just found it actually, okay looks to be regular quartz, not solar. and the front should be removable by prying off.

Correct. I did not check, seems like the bezel is removable, no pump needed. I agree with Ishima, do not try DYI that, too easy to scratch or otherwise ruin it.

skagen-hagen-black-dial-black-leather-me

  • Like 1
beearchie Member

beearchie

Posted
  • Author
Posted
7 minutes ago, Ishima said:

Some models of Skagen are sneaky, i did a little bit of googling for this model but could not find it. I was considering that it might even be solar powered, i've come across two skagens that were solar powered but did not state anywhere on the outside of the watch that it was, and they both had that line on the back with the model name in the lower right hand of the line. 

Honestly if you can't find a watch specialist who's competent to do this I strongly suggest returning to manufacturer. 
http://www.skagen.com/us/en/service-information.html

However, I will say that it is very likely that the crosshead screw on the back comes off to expose 'the setting lever' which can be pressed to release the winder and from there once you have the front off it should be possible to drop it out. 

This is enlightening!

jdm Distinguished Member

jdm

Posted
Posted
1 minute ago, beearchie said:

I have seen something like that when I took the screw out. How do I work that to pop out the crown?

Search here or on google "release stem".

  • Like 1
beearchie Member

beearchie

Posted
  • Author
Posted
5 minutes ago, Ishima said:

oh, i just found it actually, okay looks to be regular quartz, not solar. and the front should be removable by prying off, it's also a little less expensive than i assumed so I could understand some reluctance in going through a Skagen workshop, however, I will re emphasize this could go horribly wrong for you without the right experience and tools. 

Prying off the face would need something different from the regular prying knife in watch repair sets, right?

beearchie Member

beearchie

Posted
  • Author
Posted
1 minute ago, jdm said:

Search here or on google "release stem".

Goosh! I haven't even started work on the watch and I'm already excited. I am really enjoying the flow of ideas on this forum. Thanks guys!

jdm Distinguished Member

jdm

Posted
Posted
Just now, beearchie said:

Prying off the face would need something different from the regular prying knife in watch repair sets, right?

You need a sharp blade, which is kind of dangerous. Bring it to a watch repairer, not a jeweller.

beearchie Member

beearchie

Posted
  • Author
Posted
1 minute ago, jdm said:

You need a sharp blade, which is kind of dangerous. Bring it to a watch repairer, not a jeweller.

Had really nasty experiences with watch repairers. That's why I picked up watch repairs as a hobby and to try something new for myself. We learn everyday.

Will look for a sharp blade for it then.

But there is no bezel. Do I just pry at any point after taking out the crown?

beearchie Member

beearchie

Posted
  • Author
Posted
12 minutes ago, jdm said:

 

Correct. I did not check, seems like the bezel is removable, no pump needed. I agree with Ishima, do not try DYI that, too easy to scratch or otherwise ruin it.

skagen-hagen-black-dial-black-leather-me

No pain, No gain...

Right?

beearchie Member

beearchie

Posted
  • Author
Posted

Just a day on this forum and I made huge success. I was able to open the watch (there was actually a bezel at the top but hard to see) swapped the battery (621SW).

Had a tough time closing it back since I don't have a watch press. But I padded the nose of my pliers and applied gentle force till the front snapped shut.

Watch is working great now.

Thank you @jdm and @Ishima

  • Like 1
  • 4 weeks later...
abitofwill New Member

abitofwill

Posted
Posted
On 1/4/2018 at 3:56 PM, beearchie said:

Just a day on this forum and I made huge success. I was able to open the watch (there was actually a bezel at the top but hard to see) swapped the battery (621SW).

Had a tough time closing it back since I don't have a watch press. But I padded the nose of my pliers and applied gentle force till the front snapped shut.

Watch is working great now.

Thank you @jdm and @Ishima

Hi, I have the cousin to your watch (the SKW6216). Removed the screw, took off the crown.  I've managed to pop out the glass like the video instructed, with the pump method but the bezel was in the way of the everything else. Where was this bezel at the top you found? I feel so close yet so far from replacing this damn battery. :wacko:

beearchie Member

beearchie

Posted
  • Author
Posted

Look at the rim of the watch case carefully..around the 12 o clock mark. You will find a bevelled edge there. It's really hard to notice. You will need a sharp, strong blade. Pop that and the watch face will be free for you to change the battery

beearchie Member

beearchie

Posted
  • Author
Posted
10 minutes ago, abitofwill said:

Hi, I have the cousin to your watch (the SKW6216). Removed the screw, took off the crown.  I've managed to pop out the glass like the video instructed, with the pump method but the bezel was in the way of the everything else. Where was this bezel at the top you found? I feel so close yet so far from replacing this damn battery. :wacko:

Look closely at the attached photo. Hope you can see what I am referring to.

  • 1 year later...
Sazzyc New Member

Sazzyc

Posted
Posted
On 1/4/2018 at 8:56 PM, beearchie said:

Just a day on this forum and I made huge success. I was able to open the watch (there was actually a bezel at the top but hard to see) swapped the battery (621SW).

Had a tough time closing it back since I don't have a watch press. But I padded the nose of my pliers and applied gentle force till the front snapped shut.

Watch is working great now.

Thank you @jdm and @Ishima

Hey! Did you need to remove the stem before taking the front off? I was struggling to get the stem out!

jdm Distinguished Member

jdm

Posted
Posted
17 hours ago, Sazzyc said:

Hey! Did you need to remove the stem before taking the front off? I was struggling to get the stem out!

To remove the mov't you have to remove the stem first.This is true virtually for any watch.

  • 2 months later...
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Michael20
      French drum novice

      By Michael20 · Posted

      Regarding the spring winders, I made my own and used copper pipe reducers as the tubes to retain the spring. You will need to cut out a section for the end of the spring to protrude but if you watch one of the many videos on this subject that will make sense. You can find a selection of sizes on Ebay for very little cost. I'll attach a pic showing one of mine.  Good luck!
    • JohnR725
      Omega sweep second pinion friction spring - correct tension IS important

      By JohnR725 · Posted

      There were things bothering me about this discussion that took me a while to figure out the problem. In the image below it appears to be the spring may be pushing up? Normally when Omega has a spring pushing up the pinion has a pivot with a bridge to hold it in place so in other words the spring can push on something that stationary as opposed to this which appears to be floating? To understand the problem with the above image we need another image of side view which I have below. In my image down below on the left-hand side it agrees with the image up above. But the only problem is the left-hand side is defective and the right-hand side image is the way it's supposed to look. Then Omega if you can access the right documents does explain how and why this problem occurs. With the pinion floating around it might be assumed that you support it when putting on all the hands but you do not because as noted below if you do this small bush on the pinion will relocate out of position exactly what we see in the image up above.   Then Omega does not mention this but there is a possibility of also damaging the pinion and causing the bush to move to where it's not supposed to be when removing the hands.   
    • LittleWatchShop
      Regulating is too touchy

      By LittleWatchShop · Posted

      Maybe show us 1) the watch, 2) timegrapher readings in DU, DD, PU, and PD.
    • Louis1969
      Regulating is too touchy

      By Louis1969 · Posted

      The timegrapher displays significant beat error variations in the dial-up position. When the watch is lying flat (face up), the beat error is much higher than in other positions. Beat error readings are inconsistent, with especially large gaps in the face-up position.  Please help !  
    • Geotex
      Informational universe.

      By Geotex · Posted

      Looks like an open-access journal that runs as a glorified pre-print server with no true peer review, so it’s not easy to judge the veracity of the conclusions.
×
×
  • Create New...