Jump to content

crown and stem

raphael

By raphael
in Watch Repairs Help & Advice

 Share

Recommended Posts

raphael New Member

raphael

Posted
Posted

hi, i am from philippines and i would like to ask for help in finding a crown and stem for this type of watch, where can i order parts for this ? 

i have tried different watch repair here, but no one seems to give how long should i wait for them to order the parts for this watch,., thanks 

IMG_5121.PNG

Link to comment
Share on other sites
Chopin Super WRT Addict

Chopin

Posted
Posted

Honestly I would say that the only way for you to source these parts is by sending it to Breitling or trying to contact them and see if they actually offer parts to customers (which I doubt).

One other way would be to take it to a watchmaker that can order parts from breitling.

Link to comment
Share on other sites
rogart63 Distinguished Member

rogart63

Posted
Posted
4 minutes ago, Chopin said:

Honestly I would say that the only way for you to source these parts is by sending it to Breitling or trying to contact them and see if they actually offer parts to customers (which I doubt).

One other way would be to take it to a watchmaker that can order parts from breitling.

Sending it to breitling will not help much :) As it is a Tag heuer. Movement is a ETA G10 so the stem you could find from a watchmaker or maybe Ebay. It harder with the crown i think. Tag heuer supply of crowns a small. Try Cousinsuk as the have some crowns for Tag heuer. Or try contacting Tag and ask if the have any repairer in the Philippines. 

Link to comment
Share on other sites
noirrac1j Distinguished Member

noirrac1j

Posted
Posted (edited)
7 hours ago, raphael said:

hi, i am from philippines and i would like to ask for help in finding a crown and stem for this type of watch, where can i order parts for this ? 

i have tried different watch repair here, but no one seems to give how long should i wait for them to order the parts for this watch,., thanks 

IMG_5121.PNG

Good morning from Bk, NY. You can get the stem from Esslingers

https://www.esslinger.com/genuine-eta-replacement-watch-stems/#&gid=1&pid=1

 

The movement os G10.211 with date at 4: https://www.esslinger.com/eta-watch-movement-g10-211-quartz-movements-date-at-4-00-overall-height-7-4mm/?utm_medium=googleshopping&utm_source=bc&gclid=Cj0KCQjwpMLOBRC9ARIsAPiGeZAjD1Pcml4HY3QmMw6D7wGnXZ17hZzLiqoIa5XZChceiSrutNpqQFIaApdxEALw_wcB

The stem is ETA 401-1497. For the crown, you have to measure diameter. Esslinger also has many, but not sure if you can get a black one.

J

Edited by noirrac1j
typos
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ColinC
      404 Club Reboot

      By ColinC · Posted

      Speaking of 404 reboot.... I have another category of watches... Those that I wished I had not gone above £4.04 when I bid for them!!! Someone probably should have also told me to stop before I put a new stem, crown, crystal, escape wheel and then adjusted the end shake on the escape wheel. This was all on watch that had a EB 8800 pin lever movement in a worn gold plated case with a snap on case back (basically everything I try to avoid!).  
    • nevenbekriev
      Unknown mechanism

      By nevenbekriev · Posted

      The problem is that this movements were not produced with the modern level of standartization, there for parts from one didn't fit well to another, even if they may look the same. May be it doesn't concern the winding stems, but yet there are not spare parts for such movements in supply companies, not even clear calibre identification possible. And where calibre identification  is possible, there are no Ronda numbers for the balance staff or the winding stem for this calibers in the data bases.
    • ColinC
      Black coating on shock jewel metal housing

      By ColinC · Posted

      That black stuff - I had similar things happen with evaporust!  In that case I understand the evaporust eats the iron oxide away without hurting the metal but it can leave behind a layer of carbon which was in the steel that got oxidised. I spent ages trying to perfect a cleaning regime with various different stages in jars in an ultrasonic bath. In the end I switched to washing all but the balance and pallet fork in IPA and gently brushing it with a small artists brush.  I would estimate that I have found an extra 20º of amplitude doing this! It also takes me no longer than waiting hanging over a tank to move stuff to the next jar If it is really bad then I have used the IPA as a prewash and go through my old routine
    • Giogrlj
      Unknown mechanism

      By Giogrlj · Posted

      I thought is FHF. Sounds good to make winding stem by myself but I am not in watchmaking on this level. 😄
    • RichardHarris123
      Favourite timepiece.

      By RichardHarris123 · Posted

      Yes, Swatch, booooooooooo!!!
×
×
  • Create New...