Jump to content

Grandfather Clock S O S


OldEnglishYankee

Recommended Posts

https://www.watchrepairtalk.com/profile/37

Please can anyone help me? I need to find a set of. Finials for my antique long case clock. The original ones have been lost by the moving / storage company and I need to supply an estimate of the cost for the insurance . Also they have lost the key for the door and the winding handle and therefore I am unable to reassemble the clock and get him running again. I am anxious to sort this out so any advise would be very much appreciated. 

I am attaching a few photos of the clock as it is at present. Sad sight, before the move it was working perfectly. 

Thanks

image.jpeg

image.jpeg

image.jpeg

Link to comment
Share on other sites

I can only give advice not an estimate.

What you have here is a Longcase White Dial clock; it is around the 1800’s no later than 1830. The dial has what is called a moon phase dial with an arched calendar window, with second’s hand. It is an 8-day movement with strike, which strikes the hour on a bell. The case looks to be mahogany and in good proportion (it has not been cut down)

Because of what has happened it will alter its value. Many clocks don’t have their original key and the finials go missing, these can be replaced. The main problem is the key; this could be easy or hard. Find a reputable case maker; you never know he or she might just have a key that will fit. If however that fails a replacement lock will be needed. Make sure nothing is altered in finding a replacement, don’t have one with say modern screws it needs to be as near perfect to the one you have.   

Link to comment
Share on other sites

Thank you for your reply. I believe the clock to have been made by Benjamin Harlow of Lane End because of the writing on the clock face. It is a bit faded but looks like B Harlow and under that it could say Lane End . When I looked at a Long Case Clocks on various antique dealer's web sites I saw one by Benjamin Harlow which was very similar, same swan neck pediment and  general appearance . The paintings in the corners of the face are different but the moon's face is the same. I am attaching some pictures from before the move (the camera date is incorrect on photos, these were taken 2014 ) . So please let me know if you agree. 

I took these to show condition of the clock before the movers collected and put in storage. The key is in the door and the finials were wrapped up and lying on top as modern houses just don't have high enough ceilings! 

image.jpeg

image.jpeg

image.jpeg

image.jpeg

image.jpeg

image.jpeg

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Moved in. Now working out the best place to have things so moving around the room makes sense. The wooden movement testing rig may end up being suspended from the roof with some pulleys and ropes that I salvaged from some alfresco blinds that we replaced. I always seem to salvage things from things we scrap thinking, "I have an idea what I can use these for." I hope I'm not the only one that does that. My wife hates me for it. "What are you going to do with all this crap?" Anyway, here you go. If anyone has suggestions for workflow around a room, speak up. All Ideas are appreciated. The bench on wheels will carry either a laptop or my Samsung table for using with the little camera that is on the tripod for photos while dismantling etc. The small bar fridge in the corners going to have water etc in it and I might move the coffee maker from the kitchen out there as I am the only one that uses it. I want to get an ultrasonic cleaner so I may set up some sort of cleaning rig in front of the glass of the sliding door. Where the grandmother clock is currently standing. I'm hoping that I will be able to transition my working area, which is the table that the stool is sitting in front of, fairly easily between clocks and watches. I'll be doing my best to make sure that tools for each are separatedwhen stored. Logistics. I'll have a bit of wall space for being able to hang clocks if I find some that I wish to keep or hopefully at some time to be able to hang customer clocks for monitoring after servicing/repairs. The clock on the left in the blue pillow slip and the grandmother clock are earmarked for  Jarryd and his wife, Sara. He helped me move the benches in today. And then went on to tell me that ticking clocks drive him nuts. Who doesn't like the rhythmic ticking of a clock? I have a green pad for adding to the bench for a working surface. It is not a cutting mat or one of the Bergeon mats. It is actually a green desk writing mat. Was really cheap and will do exactly what I want, I think. I also have to get the sparkies back that put our new stove in to put some power points on the walls behind the benches. Hopefully this is all going to go well. I'm excited about it. It'll beat having to live out in the garage doing it. The other thing I have to do is cut a circle or square of plastic to go over the bouncing watch or clock part black hole in the middle of the floor. I would pretty much guarantee that anything that sproings off the bench would end up going straight down that drain. 😄      I think I have been on this forum about 4 years and still yet to really strike a blow. That's a bit sad isn't it. Signed up to Mark's watch course and have yet to buy the movement for working on. Have most of the tools I think I will need so now all just a matter of will.  
    • So leave off the seconds. Stand the movement on its edge, its the dial edge that rests on the pad ( either rubber or cork , something that wont slip ). Use a finger of your left hand to hold the movement upright,  right hand presses the release and flicks out the stem. I do it this way so i can see what I'm under a microscope. But you could hold the movement between two fingers of your left hand, its the right that has to manipulate the stem out by pushing the release and flicking out the stem with  right ring finger nail. Sounds more complicated than it actually is. I guess you could fix a push pin to something solid, then all you need to do is push the release against the pin, leaving your right hand completely free to pull the stem out.
    • Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
    • A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
×
×
  • Create New...