Jump to content

Mainspring replacement

Folkvisor

By Folkvisor
in Watch Repairs Help & Advice

 Share

Recommended Posts

Folkvisor Super WRT Addict

Folkvisor

Posted
Posted

I recently tried to put a mainspring in my Waltham with rather disastrous results. I broke it by putting it the wrong way - my bad entirely...

It has a hole end spring and I found it difficult getting the hole over the cleat/pin on the barrel.

Any suggestions, tricks or incantations would be appreciated.

Dave

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted

Are you using a mainspring winder? If not I think, it depends on the best way for you. I have in the past hooked the spring on before winding it in. Fit the spring in about half an inch before the hook so when you go to wind it up the spring slips on the hook, in order to do this you do not need to fit the barrel into the movement, just hold it and wind it with pin tongs. In some cases, the hook part is too close to the barrel so it needs to be bent a little, but not to much as it will rub on the spring and wear through. I am sure with practise you will find your best way.

  • Like 2
Link to comment
Share on other sites
Folkvisor Super WRT Addict

Folkvisor

Posted
  • Author
Posted

Thank you for the advice.

Excuse my ignorance but what are pin tongs? Could I use small needle-nose pliers to wind the spring? I'm thinking even a large pair of tweezers would work.

I'm sure that after breaking a couple more springs I'll be pretty good at it.

Link to comment
Share on other sites
oldhippy Distinguished Member

oldhippy

Posted
Posted
41 minutes ago, Folkvisor said:

Thank you for the advice.

Excuse my ignorance but what are pin tongs? Could I use small needle-nose pliers to wind the spring? I'm thinking even a large pair of tweezers would work.

I'm sure that after breaking a couple more springs I'll be pretty good at it.

Pin tongs or pin vices see here.

https://www.cousinsuk.com/category/pin-vices-chucks-tongs

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Murks
      Battery

      By Murks · Posted

      I think you are right wish one of the two spring should make contact do you know what one?
    • pent
      B-Dip residue?

      By pent · Posted

      So I was cleaning an especially dirty balance spring with B-dip because several turns were sticking together.  However, after a wash and dry, it seems there are more turns sticking due to the B-Dip.  I can see it clearly in-between the spring turns and it is not evaporating.  I even stretched the spring upwards a bit to let them air out and they continue to stick.  This is after two washes.  You can still see the liquid between the springs. Not sure if anyone has seen this, but I don't know if this is an indicator of my dip going bad or being contaminated.  I would rise with IPA, but the stud and collet aren't pinned--they are either glued or shellacked so I won't risk it.  If I keep seeing this, I'll probably switch back to a heptane or naphtha for this type of cleaning, but I wanted to see if anyone else has seen this with B-Dip. 
    • RichardHarris123
      Hello from slovenia

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • mikepilk
      Very useful Video

      By mikepilk · Posted

      I only watched the start, but he's out on magnification by a factor of 10. It's 7X to 45X, not 450X
    • mikepilk
      Stem removal after fitting hands

      By mikepilk · Posted

      It's one of those tools like screwdrivers and tweezers, where it's worth spending more for the quality. And it gets used all the time. At about £20, the 4040 is not expensive for Bergeon.  When putting a watch in dial down, you have to be careful not to catch a sweep second hand, but once secured, life is easy - two hands available to work on the stem.
×
×
  • Create New...