Jump to content

Victorinox Dive Master 500 Four second jump

94marconi

By 94marconi
in Watch Repairs Help & Advice

 Share

Recommended Posts

94marconi Watch Enthusiast

94marconi

Posted
Posted

Years ago I purchased a Titanium Dive Master 500 watch. I do not wear it a lot and When I went to wear it today, the seconds hand was jumping in 4 second intervals?? Perhaps a low battery issue? The watch is keeping the time and date correct albeit the time is a couple of minutes fast. The manual does not indicate this condition at all. Being waterproof to 500 meters i hate to open it up and do a battery change myself, if that is the issue. I had a new battery installed and the watch serviced and water tested by my watchmaker when I bought it off ebay as I used to do with all my watch purchases. Now that I am learning the hobby i am loath to pay some one to open it up and change the battery for me. This is a Ronda 715 movement. Do I take a chance on compromising the waterproof aspect? Or is opening the back not that big of a deal waterproof wise. Thoughts and ruminations most welcome

Ron.

Link to comment
Share on other sites
Brian3 Watch Enthusiast

Brian3

Posted
Posted

It's definitely your low battery power indicator with the four second jumps, I would change the battery myself, check the condition of the case back gasket, renew if the profile isn't round anymore, re grease the gasket and fit back making sure all contact surfaces are clean, I'd also remove the stem and crown, clean the case tube and relube it before returning the crown and stem to watch.

Obviously you can't be 100% sure your watch is water resistant without a pressure test, but if you do this you'll give it a real fighting chance.

Brian

  • Like 1
Link to comment
Share on other sites
94marconi Watch Enthusiast

94marconi

Posted
  • Author
Posted

Thanks Brian. I didn't think it would be a big deal. Just wanted to make sure. The four second jump thing is a new one on me. You would think it would be mentioned in the booklet. I was under the impression the battery was a five year job. Is it wise to leave the watch in the hack position when not in use? While that would save on battery life, would it compromise the seal on the stem with the crown not screwed down? Just glad it is a low battery. I just got my Jaxa wrench last month and now I get to play with it. :)

Link to comment
Share on other sites
94marconi Watch Enthusiast

94marconi

Posted
  • Author
Posted

Just found the receipt for the watch service and battery change with pressure test. Was done almost two years ago to the day. Cost $131.25 Can. That is a lot of money to say the least. Not begrudging the shop at all, after all they have to make a living and their work is top notch. Just that $131.00 goes along way for much needed watch oil, and we all know what that's worth. I just bought 2ml. of Moebius 9020 for $30.00. Besides, if I can change a balance staff I am sure I can Change a watch battery.

Ron

Link to comment
Share on other sites
94marconi Watch Enthusiast

94marconi

Posted
  • Author
Posted

Just had a look at the tech sheet for the Ronda 715 and it calls for a 371 battery and the life expectancy is 60 months. Sounds like I may have gotten less battery than what I paid for...or is five years just wishful thinking on the part of the manufacturer.

Sorry for all the questions.

Ron

Link to comment
Share on other sites
clockboy Distinguished Member

clockboy

Posted
Posted

 

Looking at some pics on the net: 

Victorinox Dive Master 500 is a screw back case so it should not be a problem for you to change the battery. However before re-screwing the back on (after checking the watch is functioning OK) put a tiny about of silicone grease on the case back thread. This will give a real good water proof seal.

 

 

 

  • Like 1
Link to comment
Share on other sites
  • 3 weeks later...
94marconi Watch Enthusiast

94marconi

Posted
  • Author
Posted

Finally got around to doing the battery change. No reason that i should not attempt it, Especially when one hangs out on a learned forum such as this. Just that this is a little more involved than popping in a battery in the wife's cheap disposables.

First thing to do was to get out the Jaxa wrench and loosen the case back and use a toothbrush to remove any debris that may be caught between the cover and the case.

  IMG_9037.jpg

And loosened all the way

IMG_9039.jpg

Sure takes a lot of patience to set up the wrench. One must be very careful not to scratch the watch, especially since this is Titanium and is so easy to scratch. I would not want to take a  a chance on a precious metal case. Especially if it was someone else's watch. 

Inside was the Ronda 715.5 Gold plated five jewel movement. Nice to see a bit of an upgrade from the standard movement. The 371 battery was easy to remove, being careful to not slip and damage the coil while prying back the battery retainer.

IMG_9044.jpg

It was decided to remove the movement from the case so a proper cleaning could be done. Out came the stem and the movement followed. The case, band, and back were treated to a good scrub in dish soap and hot water with a soft toothbrush. I hope the wife doesn't mind that I used her toothbrush...

IMG_9045.jpg

The gasket for the back looked in really great shape and as advised, I re greased it and the threads of the back with silicone grease. Also lubed the O ring in the stem tube and the gasket inside the crown. I took the measurements of the gaskets at the same time so I can order them when i service the watch movement at the next battery change. I do not have the proper oil yet. The hardest part was cleaning the inside of the watch crystal to perfection as well as removing all specks of dust from the dial face. Any issues here and I would be looking at them for the next couple of years.

IMG_9053.jpg

All assembled and ready for the band.

IMG_9054.jpg

The specks you see are on the outside. :) And of course the obligatory wrist shot.

IMG_9063.jpg

Love the look feel and warmth of the Titanium, but hate that it scratches so easy.

IMG_9065.jpg

Bit of a mess after an evenings work...:) 

Thanks to all for the help and advice for such a simple job...:) 

  • Like 4
Link to comment
Share on other sites
Cad101 Super WRT Addict

Cad101

Posted
Posted

Nice job goes to show what a bit of patience knowledge and advice from the kind peeps here will do. Not to mention the $130+  your saving which can now be used on more important items well done.

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Zendoc
      Chinese clone demagnetizers

      By Zendoc · Posted

      I agree - I use a magnetometer app on my iPad. A few years ago, I did invest in the Elma version of this demagnetiser. I have a background in electronics and when I cracked the unit open to explore it, I was very impressed - and reassured - by the careful attention given to the design and the quality of construction and quality of materials.  It will out-live me, and not because of any shock hazard 🙂  I find it very reliable for demagentizing watch movements, but for tools, especially elongated tools like tweezers and screwdrivers, they need to be done in sections, a couple of centimetres at a time.  I always also repeat the demagentising process several times with the object (usually a movement) oriented in several different planes - horizontally at 0 and 90 degrees and vertically.  Checking on the magnetometer app, the movement is effectively degaussed and I’ve not yet had to repeat the process. Just laying the movement horizontally and giving it a single shot sometimes works, but often doesn’t, hence my process above.  Using a compass, I doubt I’d ever know whether the process was effective or not.  The magnetometer is much more sensitive. I still use the Lepsi app, which was available for free, but which I don’t think is  available on the App Store any more.    
    • Loccolady
      Loccolady

      By Loccolady · Posted

      Hello everyone, I have just started on my  watch repair journey. Many mistakes …pinging springs and lost pallet forks !! My great Uncle was a clock maker with a royal warrant  and his ancestor stated the first hall in London so hopefully some thing rubs off . Looking forward to following the  topics on this forum 
    • Waggy
      Chinese clone demagnetizers

      By Waggy · Posted

      @RichardHarris123 I just look for a relative increase or decrease as it passes over the watch, not an absolute value. It it doesn't change much passing over the watch, than I conclude little or no magnetism, if I see the value jump from the background number, than I know I have a problem  
    • RichardHarris123
      Chinese clone demagnetizers

      By RichardHarris123 · Posted

      How accurate is it? Does it take the earths magnetic field into account, what is an acceptable reading?
    • Waggy
      Chinese clone demagnetizers

      By Waggy · Posted

      I use the same thing on my android:
×
×
  • Create New...