Jump to content

Diy Watch Hands

Lee

By Lee
in Watch Repairs Help & Advice

 Share

Recommended Posts

Lee WRT Addict

Lee

Posted
Posted

I'm having a go at putting together my own watch. I brought a case of Ebay, movement, strap etc & have almost finished a dial (once I can get to grips with my dial feet solderer!) I'm now turning my attention to making some hands & so to my question!

 

I'm thinking of making them out of stainless steel, but will this be to hard to go over the pinions? would I be better of using copper & getting it plated?

 

Lee

Link to comment
Share on other sites
Lee WRT Addict

Lee

Posted
  • Author
Posted

Since this will be my first pair of hands & I want them silver in colour & ideally matt, Stainless is ideal. But it crossed my mind all the hands I've swapped over, over the years are usually a plated softer metal & I'm not sure as to how successful fitting stainless would be.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Hi Lee, you could make the hands from anything you like provided the holes are broached to the correct dimensions to give that nice push fit. As you have been working with watches for some time now you will know when you have attained the correct hole diameter just by the feel.

Link to comment
Share on other sites
Lee WRT Addict

Lee

Posted
  • Author
Posted

mwilkes I made this prototype hand out of aluminium this morning, its a bit soft but once in the case would be ideal I think. I need to get some finer files for the real ones, I couldn't get a sharp edge (any suggestions) but I'm pretty pleased with the design, its inspired by the Rolex dial in the Bloodhound SSC land speed record car.

 

post-138-0-02700500-1401527578_thumb.jpg

  • Like 1
Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted

mwilkes I made this prototype hand out of aluminium this morning, its a bit soft but once in the case would be ideal I think. I need to get some finer files for the real ones, I couldn't get a sharp edge (any suggestions) but I'm pretty pleased with the design, its inspired by the Rolex dial in the Bloodhound SSC land speed record car.

 

attachicon.gifDSCI0004.JPG

 

I use the diamond files from Eternal Tools as they tend not to drag. Give Lucy a shout at http://www.eternaltools.com/ she will help you.

  • Like 1
Link to comment
Share on other sites
Lee WRT Addict

Lee

Posted
  • Author
Posted

wow thats a fabulous link. I brought a few bits & pieces & have done another hand in alloy to get the proportions rights (and some practice) but I'm a long way off producing something I'd be happy to put on my watch so far. I have an engraving machine that I'm using to cut the ruff hand out off which saves an immense amount of time, but once you get up close & personal under the eye glass its a whole new ball game!

  • Like 2
Link to comment
Share on other sites
  • 2 weeks later...
Lee WRT Addict

Lee

Posted
  • Author
Posted

finally had a bit of time to cut out some stainless steel. needs a lot of work thinning it down & cleaning it up, but its a start! I ordered some diamond files, degussit & some other bits & pieces now to see how patient I am!

post-138-0-99804100-1403104816_thumb.jpg

post-138-0-63639000-1403104884_thumb.jpg

 

Lets just hope I don't get a "do you know where all the knives have gone" comment at some point!

 

Lee

 

 

  • Like 1
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • ManSkirtBrew
      Accutron 218 transistors

      By ManSkirtBrew · Posted

      Update: I posted over on NAWCC and it looks like I melted the fine coil wires where they come into the solder lugs. After dropping the heat way down on my iron and being absurdly careful, I have a humming fork!
    • noirrac1j
      Rolex 2235 escape wheel jewel setting replacement

      By noirrac1j · Posted

      Hell0 @nevenbekriev. Thank you for your advice. I have removed the old setting using my staking set--I will keep the KIF spring, since it is still good.  I am awaiting the replacement setting, and will update when I do that. In the mean time, I looked at the escape wheel and it looks ok. What do you think?    
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Aloha All, I recently bought this Seitz tool on eBay, but it is missing some pushers reamers.  I ended up ordering new parts for those that were missing before I received the actual Seitz tool (bad idea).   Upon inspecting the pushers/bits, I noticed 23 of the 56 provided with the set had no numbers. Further inspection revealed a huge difference in the quality of those unnumbered.  Do all Seitz pushers/bits have a number on them?  I'm pretty sure that 33 of the 56 I received are cheap Chinese knockoffs.  The worst part is that I ordered $80 of parts to replace the missing pushers/bits, and now I'm looking to return the tool. I'm not crazy, right? If these are Seitz parts, they should all be numbered, correct? The first two pictures are the Seitz (numbered), and the other pictures are the suspect parts.  Will I even be able to get a refund?  Thanks, Frank     
    • luiazazrambo
      WWW Eterna sucked me in.

      By luiazazrambo · Posted

      It was £10 + min fee, total £16, could not leave it there. Its a Stanton A.D.2. http://stanton-instruments.co.uk/
    • Geotex
      Generic screws for unknown movements

      By Geotex · Posted

      Chief- The picture below shows the three parts from the dial side that are most useful to "fingerprint" a movement in conjunction with the diameter of the movement.  That's why forum participants are always asking for dial side photos in posts asking for identification.  As far as the setting lever screw, it actually sits loose in the main plate. The threads engage the setting lever below, and the elongated stem above the shoulder sticks through a hole in one of the bridge plates so that it's held captive if unscrewed all the way.  So you may be fine as far as that goes. 
×
×
  • Create New...