Jump to content

Brass


Recommended Posts

I have a really nice Hamilton 978 Pocket watch that I have just completed. I needed a new crystal & dial redone,and serviced the movement. The watch has a beautiful solid brass case that was very badly tarnished. I got the case all cleaned and polished to a beautiful shine with a lot of work. What is the best product if any to seal it from tarnishing again. I know they used varnish originally. Here are some before and after photos. Does anyone have suggestions .

Thanks

Capture (Small).JPG

Hamilton 978 (Small).JPG

20160717_152105 (Small).jpg

Hamilton 978 finished (Small).jpg

20160717_152050 (Small).jpg

Link to comment
Share on other sites

  • 1 month later...

Not sure if any of you have seen any of the Clickspring videos on Utube where he builds a clock from scratch but he dips the parts in the lacquer.  Would be one way to avoid brush strokes and insure 100% coverage.  Been awhile but I believe he thinned the lacquer first.  Great looking watch TimFitz.

  • Like 1
Link to comment
Share on other sites

10 minutes ago, lluvitar said:

Not sure if any of you have seen any of the Clickspring videos on Utube where he builds a clock from scratch but he dips the parts in the lacquer.  Would be one way to avoid brush strokes and insure 100% coverage.  Been awhile but I believe he thinned the lacquer first.  Great looking watch TimFitz.

Thanks I'll look for it

Link to comment
Share on other sites

1 hour ago, TimFitz said:

 

  We can't purchase  horolacq here in the USA's to dangerous, I might hurt my self or others by spraying them  , I can however buy up to four guns a month..Sometimes I cant believe the stupid laws in this country.

 

Link to comment
Share on other sites

3 minutes ago, lluvitar said:

Looks like the lacquer is thinned 50/50 before dipping.  Here's a recent video starting just before he dips it.  These videos are every bit as addicting as Mark's and make me wish I had a lathe to play with.

Dipping pendulum in lacquer

 

I can't take on any more interests, there are only so many hours in a day and patience in my wife.

Link to comment
Share on other sites

1 minute ago, TimFitz said:

I can't take on any more interests, there are only so many hours in a day and patience in my wife.

Well whether it's fortunate or unfortunate for me, I'm retired and my wife has the patience of Job.  I'll never get a lathe though, but would love to spend an afternoon or two turning some brass.  And the level of blueing he achieves on the steel is phenomenal.  

When you polished your case was it by hand or a buffing wheel.  

  • Like 1
Link to comment
Share on other sites

4 minutes ago, lluvitar said:

Well whether it's fortunate or unfortunate for me, I'm retired and my wife has the patience of Job.  I'll never get a lathe though, but would love to spend an afternoon or two turning some brass.  And the level of blueing he achieves on the steel is phenomenal.  

When you polished your case was it by hand or a buffing wheel.  

I am a full time Artist , part time computer repair geek, private Pilot, watch collector. To be honest my wife is a saint.

I got the case all cleaned up with my Dremel and good old Norwegian steam.

combine_images6.jpg

Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • does anyone knows what type of battery this digital Watch takes?  
    • Hello good watch folk ,I  just fancied a light hearted discussion after my head was starting to spin over Epilame 😅. Specifically I'm meaning the sale of vintage watches, say nothing past the 1980s market. The stuff we see on ebay and other similar sites and found at carboots, curio shops etc. And are  we thinking its reaching a peak volume ?  Younger generations clearing out passed parents and grandparents possessions.  The younger folk are not as sentimental as the old fogies ( I'm now nearly at an age that i used to think was old fogie age ). When might it have started ?  i often wish i discovered the hobby much much sooner when selling your grandfathers pocket watch at a boot sale for a few quid was just a way to offload some tat. And when might it slow down. Thoughts anyone ?
    • Yes i did eventually realise that the oil will act as a barrier, I'm sure the discussion will continue. Ive had two oleophobic coffees ( added coconut ) and in the meantime i have this just delivered to take my mind off epilame for the time being. My favourite type of dial, its a beautiful looking watch traditional English made and it runs,  the ticktock is phenomenal,  i can hear it across my living room .  You wont believe how much it was. Thats interesting about synthetic oils , i thought the same, going from a 2 year service to 5 years is a big drop in income for service folk.  I expect some did well when they embraced the use of synthetic,  probably drawing in more customers than those that didn't use the new fangled substances , i bet fairly short lived though. The more frequent service makes more sense to me, not for just the service but for the regular check up inspections that might pick up impending faults. As far as epilame goes, wouldn't it be great to be able to fumigate the complete movement in a sealed jar of heated stearic acid, 🤔 now theres a thought 😅.
    • Imm going to close the discussion by attaching the photo of my super-titanium after several vicissitudes finally working. Purchased as not working I replaced the battery and for a stroke of luck I found its semi-new solar panel which, having verified its operation, seems to recharge the accumulator perfectly. I had taken this watch almost by bet, with 40 euros I brought it back to life. The initial half idea was to resell it to finance another purchase, but.. it's definitely a nice item. It would need to check the impermeability but it's a pleasure to see it on the wrist 😃
    • In fact the secret is to go gently and find the way without forcing, and the movement enters without problems
×
×
  • Create New...