Jump to content

4 Drops Of Oil

avkxyz

By avkxyz
in Watch Repairs Help & Advice

 Share

Recommended Posts

mwilkes WRT Addict

mwilkes

Posted
Posted

I would use the oil as a hand moisturizer :-)

 

Putting oil in a dirty watch will produce an abrasive sludge that will accelerate wear on the movement. 

 

I suppose you could *cover* the movement in oil to prevent rust, but in that case you shouldn't let it run!

  • Like 1
Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

Another I got that can happen is if the old oil has turned to hard varnish, the new oil will eventually soak into it and make it swell. When this happens, the expanding varnish grips the pivots and stops the watch, this may take a week or two to manifest. This happened to me in my early days of watch servicing, all the parts had been through the ultrasonic cleaner, but there was still residue in the jewels that I had not seen. I won't make that mistake again

  • Like 1
Link to comment
Share on other sites
jdm Distinguished Member

jdm

Posted
Posted (edited)

Without service a watch, If only gives you 4 drops of oil to lubricate a movement, where should I apply the oil to? 

thank you

 

 

Lubricate pallet jewels face and balance pivots. Check a real example at http://www.watchrepairtalk.com/topic/3566-another-poor-seiko-pattern/

I do not marry the "always complete service" mantra, real life and the risk of of "mishaps" happening while trying to worship the theory taught me better.

Edited by jdm
Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • HectorLooi
      Battery

      By HectorLooi · Posted

      Try putting everything back together and closing the back cover. I think one of the two springs has to contact the metal casing to ground the casing. So when you press the button, it will touch the contact on circuit board and close the circuit.
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes, the seconds hand is the longest and goes almost to the edge of the dial. I can’t quite picture it how you do it on the rubber pad
    • Murks
      Battery

      By Murks · Posted

      A don't think so it leaked or damaged it because the watch itself works it just the buttons ain't working not connecting with the circuit board have taken more pictures of where the buttons makes contact with the circuit board.
    • Neverenoughwatches
      Stem removal after fitting hands

      By Neverenoughwatches · Posted

      I think what peter means oh is once he has fitted the hands and  checked for  alignment if them and that they dont foul, how does he then hold the movement to remove the stem in order to case up. The dial cannot be laid on a cushion or in a movement holder as the hands will get damaged. This can be quite tricky for a beginner, what i do is  to stand the movement on edge on a rubber pad so it doesn't slip. Hold the top edge with one finger then my dominant hand uses 3 fingers to press the stem release and flick out the stem. See below peter, leave off the second hand as this is the longest and gets caught the most, then fit it once the stem is out. Alternatively place the movement in one of the cup style holders, i imagine this is what they are designed for. They only touch the very edge of the dial.  
    • PeterS
      Stem removal after fitting hands

      By PeterS · Posted

      Yes I understand that. What I’m asking is, after the hands have been fitted, it’s been checked that the hands do not touch etc. then I need to remove the stem to fit the movement in the case. I have the push type, I need to turn it upside down and push the setting lever post and pull the stem out. But of course the dial and hands are in place and I have a glossy dial with lume dots and I do not want to cause any damage while it’s upside down pushing on the post of the setting lever.
×
×
  • Create New...