Jump to content

Recommended Posts

Posted (edited)

Aloha Timothy ,   I'll offer my opinion .

First off , make sure all of the battery contacts are clean . Make sure the battery is in positive side up , and not negative like the Accutrons . Examine the parts well and clean them with an eraser , or I have used contact cleaner sprayed on a small brush  and used it on the battery contact points . I would very carefully remove the balance and see where the contact points are on that . I know that the Timex electrics have a very small finger that the tip of ends near a pallet fork type of part under the balance . At this point I would not rush into making adjustments , but making observations . I see gears on the pic posted by gryf , so I would first see if gently using a pegwood stick and tickling the gears if the watch tries to go . If so I would  remove the train , clean the gears , re-lube and assemble . The jewels on the Accutron gears are capped so they can't be lubed without taking off the bridge . If you service the gears , one or two will probably try to stick to the bridge and if not careful , when you remove it the gears will come out and not give you a chance to see the stacking order of the gears and leave you guessing how they re-assemble . That happened to me on an Accutron . 

 

Take pics on all of your steps .  I have failed to do that in the past and have had a brain fart on trying to remember the order of re-assembly .  

Take small steps as you go because it probably is something simple  , like old sticky oil or a bit of oxidation on a battery part .

 

I know there are videos on Youtube on using a voltmeter to test your circuits on quartz watches and they may be useful to watch . Also getting info on the Timex forum dealing with electric watches . Install the battery and using a voltmeter , test parts of the circuit on the watch and see if you can see a pattern of how the balance coil or field get the positive and negative applied .

Edited by ricardopalamino
Posted

o.k. noted. i got sidetracked by other things, but i will be back to this one asap.

i have my phone camera all ready for documentation.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.



  • Similar Content

  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Welcome to the forum. You're best starting with something that you know runs well and keeps good time. That way when you've stripped and service it, any problems are due to something you've done.
    • Sorry to say it, but you’re very likely to break or lose something when servicing a wristwatch for the first time — I’ve been there! So, if these watches have any value to you, don’t attempt to service them as a beginner.
    • In writing "shimming the staff" I was alluding to the idea trailed in the above referenced thread of inserting a hair along the staff which, as the discussion there covered,  could result in some eccentricity. By making a (more or less) complete cylinder I was hoping to avoid that problem. Don't tell anyone, but needing a very ductile metal to do this by manipulation at such a small scale, I used a piece of an empty Tomato pureé tube! It occurred to me that the material's ductility(?) would also put less stress on the RT in forming a sufficiently tight seal. Anyway, that's how I avoided the temptation to use glue. No doubt your punctuational response to this confession will be "!!!" !
    • Hi All. I would appreciate some advice for a complete newbie on getting into watch servicing - nothing serious,  just as a fun project. I've got a thing for hand-wound watches and would like to bring an old watch (or two) back to life, so looking to learn to do a strip-clean-oil-assemble cycle.   I've toyed with this idea in the past (years ago) and picked up a couple candidates to learn on, but never found the time for them.  One is an old Ingersoll, swiss-made 17 jewels. It seems to wind and tick. Casing, dial, glass are in great shape, so looks like a good candidate to me for the first service. The other is a Benrus DR23. It winds and makes a few reluctant ticks, but then seems to stop. Casing looks like a complete gonner, and the dial is in pretty poor shape too. If the movement is not broken and just needs a service, I wonder if there's any possibility of getting a cheapo Chinese casing & dial to fit this movement in, or is it extremely unlikely to be the right size?   For a start, I want to strip & assemble a movement, perhaps a dozen times to build up the basic parts handling skills. I see that online advice is to buy a Chinese-made ST36 for this purpose. Can I just go at the Benrus or Ingersoll instead, or does it make more sense to get a cheap ST for this? Thank you.    
    • Hi,  I have this vintage Navitimer 806 with a bezel that plays a little bit as shown in this video: https://imgur.com/a/2NjdiF0 How would you fix this? I don't see where a gasket would fit for instance. Also, it seems this issue happens sometimes with older Navitimers.  Thanks
×
×
  • Create New...