Jump to content

Broken mainspring damage/repair

watchweasol

By watchweasol
in All Things Clocks

 Share

Recommended Posts

watchweasol Distinguished Member

watchweasol

Posted
Posted

Hi Guys   Got round to repairing one of my own clocks, The strike side spring had broken and it needed a clean, Managed to repair both.       the spring end and the wheel which had three teeth broken off. After cutting out the broken teeth and making and fitting a blank piece . I had to make a cutting table for the lathe and using a dremmel cutting disc re cut the blank and shaped up by hand. I have tried the interaction with the pinnion and its ok  so on to the rebuild. It is possible to do this type of repair without the use of cutting wheels and sophisticated rigs, just takes time an patience.  Done barrels before, replacing broken teeth but this is a barrel ring gear which slots onto the barrel its self (two piece) so in effect its a bit easier to do.   Although I dont post much of what I do on the forum I thought it might be interesting, Or may be not depends on your point of view.

DSCF3677.JPG

DSCF3678.JPG

DSCF3679.JPG

DSCF3683.JPG

DSCF3685.JPG

  • Like 4
oldhippy Distinguished Member

oldhippy

Posted
Posted

Not bad but you are a little out with the depth, the angle  and height on the new teeth. Next time forget the dremmel and use your needle files. The trouble with power tools they work so fast you have little or no control over them. If you use power tools make sure you have and use the correct set up for cutting teeth. 

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • BobG
      Gruen 330 balance complete

      By BobG · Posted

      Hi All, I’m having a hard time finding a balance assembly or even a working donor movement for a Gruen 330.  Any leads appreciated.   Gruen doesn’t stamp the caliber number of the movement but lust in the case back.   
    • Neverenoughwatches
      Parts sourcing for FHF 180 movement

      By Neverenoughwatches · Posted

      Why do you think this is Fontainemelon ?  The balance staff you will need to source separately.  But first it's important to accurately identify what you have there. Research Ebauches Sa, see who was in group, to find the brand that made this movement. 
    • donutdan
      Parts sourcing for FHF 180 movement

      By donutdan · Posted

      Hi Watchrepairtalk, I have some questions about part sourcing I was hoping someone here might be able to help with. I'm working on an FHF 180 movement with a broken balance staff, broken regulator pins, and damaged cap jewels (both top and bottom). Some Googling says that this is similar to other FHF calibers like 150s, 160s, 180s and so on but I can't figure out what the functional difference is between these movements.  Is there any reason I wouldn't be able to acquire a donor FHF 150 or similar (with no shock protection) and use parts from that or would it be smarter to source replacements individually? Also are there any sources someone could recommend to get bulk cap jewels like this? Thank you for the help!
    • Nucejoe
      Greetings from Whidbey Island.

      By Nucejoe · Posted

      Hello and welcome to the WRT forum.
    • JohnR725
      A lathe with indexing that won't break the bank?

      By JohnR725 · Posted

      interesting video nice to see the machine what it can do now I wonder what it costs and I'm sure it's not in my budget. Plus the video brought up questions but the website below answers the questions? What was bothering me was the size of his machine 4 mm because I thought it was bigger than that? But then it occurred to me that maybe they had variations it looks like four, seven and 10. With the seven and 10 being the best because way more tool positions in way more rotating tools. Although I bet you all the rotating tools are probably separate cost https://www.tornos.com/en/content/swissnano   Then as we been talking about Sherline. Just so that everyone's aware of this they have another division their industrial division where you can buy bits and pieces. I have a link below that shows that just in case you don't want to have the entire machine you just need bits and pieces. https://www.sherline.com/product-category/industrial-products-division/   Let's see what we can do with the concept I explained up above and bits and pieces. For one thing you can make a really tiny gear very tiny like perhaps you're going to make a watch. Then another version the center part is not separate it is all machined from one piece. Then fills gear cutting machines have gone through multiple of evolutions. A lot of it based on what he wanted to make like he was going to make a watch unfortunately eyesight issues have prevented that. Another reason why you should start projects like this much sooner when your eyesight is really good or perhaps start on watches first and then move the clocks then local we have from the industrial division? Looks like two separate motors and heads. Then it's hard to see but this entire thing is built on top of a much larger milling machine as a larger milling machine gave a very solid platform to build everything.   Then like everything else that had multiple generations are versions the indexing went through of course variations like above is one version and the one below was the last version. Now the version below I mentioned that previously and somewhere in the beginning to discussion and somebody else had one in their picture. As it is a really nice precision indexing. Then I wasn't sure if I had a the watch photos here is his unfinished watch. No he wasn't going to make a simple watch like none of his clocks were simply either what would be the challenge and that.    
×
×
  • Create New...