Jump to content

1975 Timex SSQ - Back in working order.

JerseyMo
 Share

Recommended Posts

JerseyMo Distinguished Member

JerseyMo

Posted
Posted

I have had one of these SSQ models from a huge lot won well over 10 years ago.  Problem was that as I wore it on my wrist the heat build up would cause the display to go all black.

Several times I took the module apart and carefully cleaned all contacts with alcohol and other various electronic cleaners.  No luck!  Than I would let it sit for a few more years.  A few times I tried to swap in a display glass from other modules.  Again no luck.

Finally the other week I got lucky and swapped in a new glass and it worked.  But....   I noticed that some segments were not appearing on the second digit.  Was my fault because on of the contacts between the circuit board and the glass was damaged when I lifted it off.  What to ?  Lets go search eBay and find one right?  And sure enough I found one listed as "Parts or Repairs" BIN make offer and for just about 10 bucks one was on its way.   Yes, I know  what your thinking...the one coming it was going to have issue too and now instead of one broken SSQ I'd have two.   

Well, I guess I got lucky because here she is...

 

 

 

310483993_703823587286642_8034098935889945213_n.jpg

So why did I go through all the fuss?  Easy, 1975 was the first year Timex introduced an LCD watch and it has a unique feature.  Which is that unlike most LCD modules that require two or more push buttons, this one only has what looks like a typical crown.  You turn it and the minutes count up, turn it back and turn it again and the hours count up.  Plus 1975 was the year I graduated HS.

Won't it be cool to wear this to the 50th reunion that is only 3 years away.

 

  • Like 4

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Nucejoe
      Greetings from Whidbey Island.

      By Nucejoe · Posted

      Hello and welcome to the WRT forum.
    • JohnR725
      A lathe with indexing that won't break the bank?

      By JohnR725 · Posted

      interesting video nice to see the machine what it can do now I wonder what it costs and I'm sure it's not in my budget. Plus the video brought up questions but the website below answers the questions? What was bothering me was the size of his machine 4 mm because I thought it was bigger than that? But then it occurred to me that maybe they had variations it looks like four, seven and 10. With the seven and 10 being the best because way more tool positions in way more rotating tools. Although I bet you all the rotating tools are probably separate cost https://www.tornos.com/en/content/swissnano   Then as we been talking about Sherline. Just so that everyone's aware of this they have another division their industrial division where you can buy bits and pieces. I have a link below that shows that just in case you don't want to have the entire machine you just need bits and pieces. https://www.sherline.com/product-category/industrial-products-division/   Let's see what we can do with the concept I explained up above and bits and pieces. For one thing you can make a really tiny gear very tiny like perhaps you're going to make a watch. Then another version the center part is not separate it is all machined from one piece. Then fills gear cutting machines have gone through multiple of evolutions. A lot of it based on what he wanted to make like he was going to make a watch unfortunately eyesight issues have prevented that. Another reason why you should start projects like this much sooner when your eyesight is really good or perhaps start on watches first and then move the clocks then local we have from the industrial division? Looks like two separate motors and heads. Then it's hard to see but this entire thing is built on top of a much larger milling machine as a larger milling machine gave a very solid platform to build everything.   Then like everything else that had multiple generations are versions the indexing went through of course variations like above is one version and the one below was the last version. Now the version below I mentioned that previously and somewhere in the beginning to discussion and somebody else had one in their picture. As it is a really nice precision indexing. Then I wasn't sure if I had a the watch photos here is his unfinished watch. No he wasn't going to make a simple watch like none of his clocks were simply either what would be the challenge and that.    
    • Titanium
      Lab Coats

      By Titanium · Posted

      Use a Portwest Howie lab coat. They are the biological type so they have tapped cuffs so you don't end up getting the loose cuffs of normal lab coats catching everything. 
    • Titanium
      Chinese tools debate

      By Titanium · Posted

      Some of the Chinese tools ae great and can be purchased at a fraction of the price of Swiss ones, some are complete garbage and some I'm convinced are coming out the same factory as the branded ones.
    • caseback
      Calendar work certina 25-651

      By caseback · Posted

      I found this string about this problem. I've not gone through it all, but I believe it also mentions making a spring. If not in this string, the info is online.
×
×
  • Create New...