Jump to content

Hello, not even a beginner yet.

EHam

By EHam
in Introduce Yourself Here

 Share

Recommended Posts

EHam New Member

EHam

Posted
Posted

But I've very much been interested in watchmaking for a very long time.   So, I'm thinking about taking the course, and giving it a go.  (I wonder if this old dog can learn some new tricks?)

In any case, I'm likely to ask some dumb questions along the way that may cause others vicarious embarrassment.  So, I offer my apologies in advance. 

 

 

 

grsnovi Distinguished Member

grsnovi

Posted
Posted

Welcome to WRT! I've taken Mark's online courses (1 - 3) and they're going to teach you a lot (especially as a "not-even-a-beginner").

There are some really helpful folks here. When you ask your questions, be sure to attach a photo of what you're working on. You might also edit your profile to let us know where you are in the world (there are folks here from all over the place).

I started with this whole thing about 7 months ago and I have learned a lot here (and from watching YT videos). I'm still not very adept at doing the actual work (but I have a lot of fun photographing what I'm doing).

- Gary

  • Like 1
ManSkirtBrew Super WRT Addict

ManSkirtBrew

Posted
Posted

Welcome! I've also taken the first three levels of Mark's courses and found them worth the money.

There is, however, no substitute for experience, and don't be discouraged when your first few eBay finds don't work out well.

The ST36/6497 clone movement from eBay is a good place to start. You can pick one up brand new for less than $40 and not have to deal with busted-up watches and broken parts while learning how to disassemble and assemble a watch.

I'm pretty sure that's the movement Mark recommends in his course, as well.

And finally, ask the dumb questions. We've all been there (many of us still are, speaking for myself).

  • Like 1
  • Thanks 1
thor447 WRT Addict

thor447

Posted
Posted
10 hours ago, EHam said:

But I've very much been interested in watchmaking for a very long time.   So, I'm thinking about taking the course, and giving it a go.  (I wonder if this old dog can learn some new tricks?)

In any case, I'm likely to ask some dumb questions along the way that may cause others vicarious embarrassment.  So, I offer my apologies in advance. 

 

 

 

Welcome to WRT.  Your username is oddly similar to someone I know.  You by chance aren't in central Oklahoma are you?  Slim chance but I figured I'd ask.

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing

  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • Simeon
      Oiling Dubois Depraz chrono module pivots (Omega Speedmaster Reduced)

      By Simeon · Posted

      Righty ho, I re-serviced the chrono module and got a reasonable result with minimal loss of amplitude when not running the chrono and about 30 degrees loss when running. Great. The problem is now that the chrono (and movement) stops running after about a minute or so, a tap on the watch starts it running again. No issues with the movement running when the chrono is stopped. Going to service it yet again, obviously some residual issues with friction in the chrono module (Very frustrating - I wish there was some way of testing it as I go!) I also seem to have a problem with the cannon pinion where the movement is running continuously (with the chrono stopped) but it's losing significant time / stopping. This is one of those two piece ETA style with a driving wheel pressed over the cannon pinion, obviously arranged for driving the chrono module. I had no issues with this prior to service and just added a small amount of grease between the driving wheel and the centre cannon pinion as the technical guide required. What's the best way of tightening these up? I would like to replace it but I guess this is going to be hard to find as it is dedicated to the DD chrono movement. 
    • caseback
      Chinese tools debate

      By caseback · Posted

      He uses the micrometer cap, but he leaves the spring out (you can see that in the video). If you leave the spring in, the spindle will move up as well (as shown by @Knebo).
    • Malocchio
      Chinese tools debate

      By Malocchio · Posted

      Seems like he doesn't have the micrometer cap  attached to the spindle so he can only push down but cannot pull up? If the cap screws into the spindle I guess you don't need the spring? I only have a "normal" Seitz so I really have no idea. 
    • Edwinsh21
      Christopher Ward SH21 Winding Rotor Bearing replacement

      By Edwinsh21 · Posted

      Do you have a part number for the bearing shim lock tool?
    • Dell
      Lathe motor advice

      By Dell · Posted

      Yes in my opinion the 3/4HP is plenty but it’s your decision & yes it does come with speed control but foot operation so my reason for changing to potentiometer was because my leg shakes so it was like me revving the lathe & anyway I prefer to set the speed. I & a few others that I recommended the motor to run a Pultra 10mm lathe so if you have a 6 or 8mm B & L then it will be plenty, if you have seen any of my videos you will have seen that when using a graver I run quite slow without any problems. Dell
×
×
  • Create New...