Jump to content

Hello, not even a beginner yet.

EHam

By EHam
in Introduce Yourself Here

 Share

Recommended Posts

EHam New Member

EHam

Posted
Posted

But I've very much been interested in watchmaking for a very long time.   So, I'm thinking about taking the course, and giving it a go.  (I wonder if this old dog can learn some new tricks?)

In any case, I'm likely to ask some dumb questions along the way that may cause others vicarious embarrassment.  So, I offer my apologies in advance. 

 

 

 

Link to comment
Share on other sites
grsnovi Distinguished Member

grsnovi

Posted
Posted

Welcome to WRT! I've taken Mark's online courses (1 - 3) and they're going to teach you a lot (especially as a "not-even-a-beginner").

There are some really helpful folks here. When you ask your questions, be sure to attach a photo of what you're working on. You might also edit your profile to let us know where you are in the world (there are folks here from all over the place).

I started with this whole thing about 7 months ago and I have learned a lot here (and from watching YT videos). I'm still not very adept at doing the actual work (but I have a lot of fun photographing what I'm doing).

- Gary

  • Like 1
Link to comment
Share on other sites
ManSkirtBrew Super WRT Addict

ManSkirtBrew

Posted
Posted

Welcome! I've also taken the first three levels of Mark's courses and found them worth the money.

There is, however, no substitute for experience, and don't be discouraged when your first few eBay finds don't work out well.

The ST36/6497 clone movement from eBay is a good place to start. You can pick one up brand new for less than $40 and not have to deal with busted-up watches and broken parts while learning how to disassemble and assemble a watch.

I'm pretty sure that's the movement Mark recommends in his course, as well.

And finally, ask the dumb questions. We've all been there (many of us still are, speaking for myself).

  • Like 1
  • Thanks 1
Link to comment
Share on other sites
thor447 WRT Addict

thor447

Posted
Posted
10 hours ago, EHam said:

But I've very much been interested in watchmaking for a very long time.   So, I'm thinking about taking the course, and giving it a go.  (I wonder if this old dog can learn some new tricks?)

In any case, I'm likely to ask some dumb questions along the way that may cause others vicarious embarrassment.  So, I offer my apologies in advance. 

 

 

 

Welcome to WRT.  Your username is oddly similar to someone I know.  You by chance aren't in central Oklahoma are you?  Slim chance but I figured I'd ask.

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • mbwatch
      Bad design or worst design?

      By mbwatch · Posted

      No real question here, I managed to clean and reinstall this straight. But I just thought I would share this silly design for a balance cap jewel on an old Junghans pocket watch caliber J32. The screw is in the center, the jewel eccentric; the opposite design from every other cap jewel I have ever seen. But it has no steady pins beneath so tightening the screw means the cap jewel wants to rotate away from the hole jewel. Without an automatic oiler, this took about 6 tries to oil and screw down the cap without spinning it away. A tiny bit of Rodico didn't really help. Happily they don't make them like this anymore.
    • djwilliams37
      Rotary skeleton part identification

      By djwilliams37 · Posted

      Thanks for your most appreciated assessment with this. I will purchase a new movement. 
    • Terrinecold
      First movement = First broken movement

      By Terrinecold · Posted

      Sorry I am confused by step 4. Which screw? There is the balance cock screw. I don’t think that is what you are talking about. The only other screw I see is on the side of the swan neck regulator. I do t think that is the one you are talking about either Well I managed to make it worse again but I could take pictures.  I had put the balance cock partially in place with one locator pin in. I wanted to remove it and I know I should use my screwdriver in the slot to move it off the pin but I didn’t l pulled wit my tweezers and it stuck then gave suddenly and was thrown a few inches away and of course the hairspring got tangled (a coil was above the cock) and untangling it from the cock deformed it.    I am going to try to put it back in shape and I will likely post more pictures after shortly. I’ll wait for feedback before reattaching it to the cock I am sorry I think I’ll give up. I was trying to remove the tangle. I had previously succeeded but now I just made more of a mess with this new tangle.  Lf you see my spring it is now just a knot.  Let’s keep a positive attitude. The movement was already broken. It was working but couldn’t be used. So what if it can’t run anymore… I went on and reinstalled the mainspring in the barrel by hand and managed to put the arbor back in.  Now I need to close the thing!  
    • RichardHarris123
      Hello!

      By RichardHarris123 · Posted

      Hello and welcome from Leeds, England. 
    • nevenbekriev
      First movement = First broken movement

      By nevenbekriev · Posted

      OK, bad video... Almost all of them are. To attach the spring (stud) to the cock: 1. Put the cock on the table top upside down.  Open the regulator if closed. 2. Put the balance on , align the stud above the hole for it in the stud carrier. 3. Help the stud to get in the hole by gentle pressing. 4. When it is in, grasp the cock with balance with tweezers (from aside, not from above), then get it between fingers, not changing the horizontal position, then tighten slightly the screw. This is the moment to correct the high position of the stud - it's top must be even with the carrier. Now tighten the screw. 5. If the outer coil is out of the regulator, move the regulator to the max to '+' position, then guide the spring to get in the regulator. Now You can return the regulator where it was and close it above the spring
×
×
  • Create New...