Jump to content

Main Spring Replacement, What Do I Need?

No8yogi

By No8yogi
in Watch Repairs Help & Advice

 Share

Recommended Posts

Mark Distinguished Member

Mark

Posted
Posted

That's annoying. :(

 

The only thing you can do is gently squeeze it, most likely without the arbor in place. But it is very risky - the spring is very brittle but can bend a small amount. Baby steps - be very very careful and don't apply pressure where the hole (for the hook) is because that is the weakest part.

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

I had the same problem a few months back. I very gently eased it into a tighter curve using round nosed pliers. As Mark says, make sure that you do not bend it where the hole for the hook is. Ideally it should be slightly tighter than the circumference of the arbour to make sure that it grips it when fitted. It worked for me, but be very careful.

  • Like 1
Link to comment
Share on other sites
No8yogi WRT Addict

No8yogi

Posted
  • Author
Posted

Going to bed!!

Got the mainspring sorted train running nicely

It just won't tick! Hairspring looks good balance turns smoothly

The it happened the winder frikin broke off!!!!?!!!!

Snapped clean in half I can't be bothered to go find it suffice to say I am gutted

Link to comment
Share on other sites
Geo Distinguished Member

Geo

Posted
Posted

That's a real bummer about the stem, I hope you can track down another.

Regarding the watch not ticking, if the spring is still wound try this first.

Remove the the balance and ensure that the escapement lever flicks sharply from side to side when touched very delicately with a dry oiler. If it does then you probably put the balance wheel in the wrong position regarding the escapement lever. Looking down on the escapement lever, if the lever is resting to the right, make sure that the roller jewel on the balance is rotated further to the right than the end of the lever so that it will catch the end of the lever when it rotates to the left. If you do this the balance should start up as you locate the cock on the main plate. The reverse of this is true if the balance lever is initially resting to the left.

If the escapement lever does not flick sharply from side to side with the balance wheel removed, the problem could be that you oiled the escapement jewels. They should be free from oil. Failing this you will have to completely strip the watch and check every component in detail followed by staged assembly testing each set of mating components as you go.

Bast of luck............and don't give up!

Link to comment
Share on other sites
Mark Distinguished Member

Mark

Posted
Posted

As Geo said - don't give up. It can be discouraging when this happens.

My advise is to always take a step back when things are not going right. If you start feeling frustrated when a repair is going wrong then stop! Come back to it after you have cleared your head. Go for a drive or watch some telly

When you come back to the job you should be calm and ready to tackle it again.

In short, it is very difficult to fault find when you are in a frustrated state.

Having said all that, we all make mistakes from time to time. So just take a breath and then go back to it with fresh eyes.

Good luck mate :)

Sent from my iPhone using Tapatalk

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • noirrac1j
      Rolex 2235 escape wheel jewel setting replacement

      By noirrac1j · Posted

      Hell0 @nevenbekriev. Thank you for your advice. I have removed the old setting using my staking set--I will keep the KIF spring, since it is still good.  I am awaiting the replacement setting, and will update when I do that. In the mean time, I looked at the escape wheel and it looks ok. What do you think?    
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Aloha All, I recently bought this Seitz tool on eBay, but it is missing some pushers reamers.  I ended up ordering new parts for those that were missing before I received the actual Seitz tool (bad idea).   Upon inspecting the pushers/bits, I noticed 23 of the 56 provided with the set had no numbers. Further inspection revealed a huge difference in the quality of those unnumbered.  Do all Seitz pushers/bits have a number on them?  I'm pretty sure that 33 of the 56 I received are cheap Chinese knockoffs.  The worst part is that I ordered $80 of parts to replace the missing pushers/bits, and now I'm looking to return the tool. I'm not crazy, right? If these are Seitz parts, they should all be numbered, correct? The first two pictures are the Seitz (numbered), and the other pictures are the suspect parts.  Will I even be able to get a refund?  Thanks, Frank     
    • luiazazrambo
      WWW Eterna sucked me in.

      By luiazazrambo · Posted

      It was £10 + min fee, total £16, could not leave it there. Its a Stanton A.D.2. http://stanton-instruments.co.uk/
    • Geotex
      Generic screws for unknown movements

      By Geotex · Posted

      Chief- The picture below shows the three parts from the dial side that are most useful to "fingerprint" a movement in conjunction with the diameter of the movement.  That's why forum participants are always asking for dial side photos in posts asking for identification.  As far as the setting lever screw, it actually sits loose in the main plate. The threads engage the setting lever below, and the elongated stem above the shoulder sticks through a hole in one of the bridge plates so that it's held captive if unscrewed all the way.  So you may be fine as far as that goes. 
    • Chief
      Generic screws for unknown movements

      By Chief · Posted

      So I found what I believe is the setting lever screw! Am I right in thinking the screw next to the click is the correct one for the setting lever? However if it is, it doesn't fit in the hole which I believe is for it! I can get the lever to sit nicely on the stem and line up with a hole, but the screw only goes as far as the shoulder and stops. It's as though the hole is too small! The dial side has been disassembled by the way, the other wheels are in my tray
×
×
  • Create New...