Jump to content

Ifixit Videos

Rob
 Share

Recommended Posts

Rob WRT Addict

Rob

Posted
Posted

iFixIt, a site mostly known for their DIY repair info and disassembling the latest tech gadgets recently posted two videos about mechanical watches as a followup to all the Apple watch news. Part of a trend where mechanical watches become popular as a result of the new smartwatches.

 

 

 

Link to comment
Share on other sites
Ishima Super WRT Addict

Ishima

Posted
Posted

Always makes me kind of sad to not have the opportunity to go to a proper watchmaking school.

I'll just have to keep reading about, watching videos, and practicing on scrap mechanical movements and maybe in a few years i can transition to working on mechanical as well as all the quartz work I still very much enjoy.

  • Like 1
Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.
Note: Your post will require moderator approval before it will be visible.

Guest
Reply to this topic...

×   Pasted as rich text.   Restore formatting

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • eccentric59
      404 Club Reboot

      By eccentric59 · Posted

      I went with 8.90£ because 12th century Italian mathematicians are always excellent topics to bring up when trying to get your guests to go home. 
    • Zendoc
      Without Our Forum

      By Zendoc · Posted

      As a beginner, I’ve found this forum invaluable. I doubt I would’ve persevered without its support. I’ve had the confidence to attempt things that seemed to me impossible only because I knew there were patient and giving folks gathered around this watering hole, available to share their skill.    I would very much like to know where to go if this one dries up and everyone needs to decamp.  There’s something special about the folks gathered in this group.  How to keep in touch?  
    • eccentric59
      Boley lathe motor silly question.

      By eccentric59 · Posted

      After a 3-week work fiasco that took up 137% of my time, I was finally able to get back to restoring a G. Boley 8mm lathe I picked up on eBay. I still need to do a bit of polishing on the tailstock but it works very nicely. Before and after pictures below. In any case, when I was reassembling the motor I wasn't quite sure which side the pully attached to, or if it matters. My question is ... does it matter? The listing photo below shows it the reverse of how I have it now, but it seemed that the cord and the reversing lever(s) should be on the right away from the belt.   
    • Zendoc
      Deciphering mainspring specifications…

      By Zendoc · Posted

      Thanks Richard.  That’s clear.   So - another question - how much latitude is there in barrel and spring sizing? Say I have have measured the ID of my barrel to be 9mm and (all other mainspring specs being equal), the closest match I can find for a replacement mainspring is listed with an 8.5mm barrel size, is it acceptable to fit the smaller spring in to the slightly larger barrel without compromising anything functionally?  I’m in this situation now with an AS 1686 which has a 9mm barrel, but the closest replacement I can find has an 8.5mm diameter listed in its specs.  I can find an alternative 9mm spring, but would have to accept a different thickness.  I’m unsure how much wriggle room is acceptable, or whether in mainspring sizing, there’s a priority - ie thickness over barrel size etc. Thanks again for any info.  Cheers, John  
    • tomh207
      Without Our Forum

      By tomh207 · Posted

      We already have a Facebook group run by Mark , so this is a bit moot. Search for “Watch repair lessons” group.   Tom
×
×
  • Create New...