Jump to content

Elgin 448 Cap stone removal


mikecj

Recommended Posts

All,

I am working on an Elgin 448 watch. It is almost 90 years old and had a lot of crud on it. I'm working on the balance  trying to remove the cap stone (jewel) in order to clean it. I managed to remove the two small screws (locations in red) that hold it in place without to much trouble. However I cannot remove the jewel because of the brass inserts surrounding it (locations in yellow). 

I thought about applying heat or cold but am worried about damaging the hairspring.

Any suggestions? Attached is a picture of the unit.

Thanks, 

MikeCJ

IMG_20220120_130341890_LI.jpg

Link to comment
Share on other sites

The cap jewel is mounted in the brass insert, you do not remove it !

First remove the balance + hairspring - v carefully !

Take out the two screws, then turn the cock over, and push the jewels out from below. 

You will then have the hole jewel, in a brass surround, and the cap jewel, also in a brass mounting.

I have an old Elgin 455 which I've just pushed the (very dirty) jewels out to show you -

0001.thumb.jpg.455f9f064ffda4a8f92c1043b93d298c.jpg

0002.thumb.jpg.06daf13d7eb498a4dcf4cee4d32cb549.jpg

 

Edited by mikepilk
Link to comment
Share on other sites

21 minutes ago, mikecj said:

I thought about applying heat or cold but am worried about damaging the hairspring.

If you had a blowtorch you should Be able to melt the brass and get the jewels free. Unless of course you're trying to service the watch then this would be a really bad idea.

I'm assuming this is your first pocket watch?

What you want to do is loosen the stud screw push the stud out a little bit not too far so it's loose remove the balance bridge remove the balance wheel Keeping the hairspring on the balance wheel of course. Because if you going to clean the watch you have to take the balance wheel out anyway.

To understand the jewels I have a picture. The jewels are burnished into brass settings. This is why blowtorch would be a bad idea because you want to keep them in the settings.

Then because I was too slow to answer somebody beat me to the answer with nice pictures I think you get an idea of how it all goes together or comes apart

jewels American pocket watch balance in settings.JPG

  • Haha 2
Link to comment
Share on other sites

Mike is on the money,

JohnR is kidding,( too many help and advice to give) 

Remove the balance first to get it out of harms way.

Give the cock assembly a 48 hr soak in Coca cola or a bath in ultrasonic or use penetrating oil .

The end stone is happy in the brass plate, thats where is suppose to stay, all you need is to gain access to otherside  and clean it real good.

Good luck 

Link to comment
Share on other sites

52 minutes ago, Nucejoe said:

Give the cock assembly a 48 hr soak in Coca cola or a bath in ultrasonic or use penetrating oil .

The end stone is happy in the brass plate, thats where is suppose to stay, all you need is to gain access to otherside  and clean it real good.

Traditionally on American pocket watches to clean the balance jewels they have to be pushed out. The screws have to come out but there's a problem with that? The screws at some point in time will end up getting stripped that's an issue. At one time they made oversized screws to fix the problem but you're not going to find those. The preferred way would be to just clean it with a decent ultrasonic machine but it depends on how bad the lubrication is as to whether you can clean it out or not when it's assembled.

Link to comment
Share on other sites

8 minutes ago, JohnR725 said:

Traditionally on American pocket watches to clean the balance jewels they have to be pushed out. The screws have to come out but there's a problem with that? The screws at some point in time will end up getting stripped that's an issue. At one time they made oversized screws to fix the problem but you're not going to find those. The preferred way would be to just clean it with a decent ultrasonic machine but it depends on how bad the lubrication is as to whether you can clean it out or not when it's assembled.

I didn't mean cleaning with the endstone on cock assembly. OP needs to check the other side of end stone to make sure its in good condition, suggested soaking cuz op says there is  lots of crud is on it. 

Regards 

Link to comment
Share on other sites

14 hours ago, JohnR725 said:

 The screws at some point in time will end up getting stripped that's an issue. At one time they made oversized screws to fix the problem but you're not going to find those. 

I've come across the stripped screws many times (e.g. the left screw in the above movement). I didn't realise they made oversize screws to fix the problem. I use a tiny drop of Loctite.

Edited by mikepilk
Link to comment
Share on other sites



  • Recently Browsing

    • No registered users viewing this page.
  • Topics

  • Posts

    • Thanks so much for all the tips! I tried both methods. I tried pulling the pins with two pliers but they wouldn't budge. I then tried the method shown in the clip but that was way too much effort and I was pretty sure the bracelet would not have looked right once I was done. I ended up getting a similar bracelet that's easy to resize but I'm glad we gave this a shot.
    • Yes. This machine can function in 2 modes, soldering and spot welding. The spot welding mode can be used for broken screw removal as well as repairing broken mainspring bridles. If your DIY one works fine, then there is no need to buy another machine. But if you are thinking of buying a new machine, I suggest you wait awhile because I heard that there is a new machine under development that in addition to the above 2 functions, has a 3rd mode that can be used to fill pits in corroded metal surfaces.
    • Thanks for clearing that up, I was just going by how it appeared to work in the few videos I had seen on line, especially comparing it to my own manual current based jobby, when they was showing it being used to remove a broken stem it seemed to weld as no solder paste was used. I will see if I can find the video. Did seem to work very well though, just trying not to buy it as my DIY one seems to work ok and i dont do enough to justify the cost, but ghen again we do seem to say that a lot Found the video It's on this sellers page https://a.aliexpress.com/_mtyFJxo You can see solder paste being used for the dial foot but not when removing the broken stem from the crown, it looked to me to be more like the flash from a spot welder which was why I thought it was based on a capacitor discharge like one of those spot welders used for battery pack assembly.
    • Well what do you say, if this is the work of a reputable clock repair it’s pretty poor. It is definitly needing a rebush. What Old Hippy has said holds true. The old bush out the hole tidying up and a new bush pressing in. I my self would drill the hole to remove the punch marks and make a bush to restore the plate but for that you need a lathe. Looking at the bush the condition of the pivot may also need attention, burnishing at the least to restore the surface. It’s not impossible to do it by hand , but will take care and time.
    • Thanks old hippy Its  shame really as it was purchased from a reputable clock repairer for not an inconsiderable sum. As you say it has been botched; even I can I can see that and I'm not a clock repairer.  Plugging holes sounds quite technical; what's involved please? I'm trying to weigh up how much of this I can do myself.  Thanks so far.
×
×
  • Create New...