Jump to content

Lorus Analogue/Digital copper tail

WatchWood

By WatchWood
in Watch Repairs Help & Advice

 Share

Recommended Posts

WatchWood Member

WatchWood

Posted
Posted

Hopefully someone can enlighten me?

The image below is from a Lorus with analogue and Digital display that I bought a few months ago. All was good until last week when the analogue hands started losing time. I assumed the battery was in need of changing so replaced both - there is a second battery under the one you can see. Unfortunately the problem persisted.  Lacking any test equipment I did the next best thing and held the watch to my ear. The 'tick' sounded regular until the second hand got to the same section (about 20 seconds) when it was obvious the hand was struggling to move.

After a long head-scratch I noticed the coil of copper that comes from the digital display circuit board (the one just above the battery in the image) and makes contact with the case back. Being loose I removed it and replaced the case back. The watch returned to keeping  perfect time again (for days). Putting the coil back reproduced the problem. It seems the coil is too long and the pressure from the case back is causing the hands (or stem) to bind somewhere. Simple solution was to shorten it. The 'ear' test suggests the issue has largely resolved itself (along with the time-keeping).

What I'm curious about though is what does this coil of wire do? - with or without, the watch functions!

Thanks

PS I should have sent the watch back as it is (was!) still in warranty but where's the fun in that?

Lorus anadigi.jpg

Link to comment
Share on other sites
WatchWood Member

WatchWood

Posted
  • Author
Posted

Yes he was right. After a bit of tweaking I've now fixed it so the alarm/chime works without putting pressure on the movement below. The watch also keeps time. Not sure why it happened in the first place but it definitely seemed to be longer than it needed to be.

Thanks again.

Link to comment
Share on other sites
HectorLooi Distinguished Member

HectorLooi

Posted
Posted (edited)
11 hours ago, WatchWood said:

Lacking any test equipment I did the next best thing and held the watch to my ear. The 'tick' sounded regular until the second hand got to the same section (about 20 seconds) when it was obvious the hand was struggling to move.

OMG! You can hear a quartz watch tick? You must be young. I don't think I could hear a quartz watch tick by the age of 30.

Anyway, that little coiled spring is an electrical connection, usually for contacting the piezo sounder on the caseback or sometimes between a upper and lower circuit board.

Edited by HectorLooi
Remove some text
Link to comment
Share on other sites
WatchWood Member

WatchWood

Posted
  • Author
Posted
5 hours ago, HectorLooi said:

OMG! You can hear a quartz watch tick? You must be young. I don't think I could hear a quartz watch tick by the age of 30.

 

No, not so young unfortunately. I now need glasses to read but for some reason my hearing seems to getting more sensitive!!

Link to comment
Share on other sites
 Share
Go to topic listing


  • Recently Browsing

    • No registered users viewing this page.

  • Topics

  • Posts

    • rjenkinsgb
      Help Identifying movement

      By rjenkinsgb · Posted

      It looks similar to some AS movements, but it's not identical to any I can find. There may be a logo / number under the balance wheel??  
    • rjenkinsgb
      Accutron 218 transistors

      By rjenkinsgb · Posted

      Many would disagree: https://www.rohm.com/products/faq-search/faqId/234 https://uk.farnell.com/c/semiconductors-discretes/transistors/bipolar-transistors/pre-biased-digital-bipolar-transistors https://uk.rs-online.com/web/p/bipolar-transistors/8232832P?gb=s https://uk.rs-online.com/web/p/bipolar-transistors/0580240?gb=s (RS don't have a specific category, but over 1000 "digital transistor" items).  
    • Hawaiikook808
      Seitz Tool - Help determine if Seitz or not

      By Hawaiikook808 · Posted

      Thanks, ManSkirtBrew.  I started looking for a setup like yours and ran across this.  It was about half the price of the JKA Feintaster (depending on what auction you were in), and it's a Bergeon.  I bought it because I thought the price was fair (eBay - Buy it now), and I'm a sucker for vintage tools. It also has a table, so it should be easy to use for measuring jewels. I wonder if the the contact points can be changed out. Bergeon seems to manufacture new tables and accessories for the contemporary dial version. What do you guys think of it? I'm sorry this post seems to have taken a detour. I'm new here so let me know if I should start a new topic.
    • nevenbekriev
      Winding pinion making

      By nevenbekriev · Posted

      This is a flying cutter, usual one. The cutter itself is shown in the pictures in the first message, it is made of broken tungsten carbide drill bit. I asure that all the angles of the cutter are as they should be. I have video - little older one - that I made when onse making the same kind of winding pinion for a Poljot 2200, which is even smaller than this one. It is not easy to see in the video, but the tool rest moves about 1mm towards the object in Y direction and then returns back untill cutter is rotating. Then the spindle is rotated one tooth ahead and everything repeated untill all teeth are cut.
    • Trav2004
      Help Identifying movement

      By Trav2004 · Posted

      After a bit further research could it possibly be an AS 970?
×
×
  • Create New...